Reviewed by the Benton Metal Depot team · Updated
For some residents in Colemans Lake, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Emanuel, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Delivery to Colemans Lake is currently estimated at 1 to 2 weeks.
- ◦Benton Metal Depot is approximately 52.7 miles from Colemans Lake.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
74
As of 2026 · Source |
Permits & Setbacks in Emanuel County
Emanuel's permitting office, Emanuel County Building Inspection & Code Enforcement Department, sets the accessory-structure line at 200 square feet — build under that and you generally skip the full building-permit process, though a setback of Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Colemans Lake
Residents in Colemans Lake are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 52.7 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Emanuel County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Colemans Lake before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Colemans Lake?
Current delivery time to Colemans Lake is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How far is Benton Metal Depot from Colemans Lake?
Benton Metal Depot's Statesboro location is approximately 52.7 miles from Colemans Lake. The company serves residents throughout Emanuel, including communities such as Gertrude, Magruder, Summertown and Midville. Current delivery time for a metal garage to the Colemans Lake area is about 1 to 2 weeks.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Emanuel County Building Inspection & Code Enforcement Department has requirements that can affect garage placement, including a current setback of Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How close can my metal garage be to the property line?
The current setback in Colemans Lake is Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process., although you should confirm the requirement for your particular property with Emanuel County Building Inspection & Code Enforcement Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
Colemans Lake, Emanuel County — At a Glance
- Permit Authority Name
- Emanuel County Building Inspection & Code Enforcement Department
- Permit Authority Url
- https://www.emanuelco-ga.gov/419/Building-Permit-Application
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 52.7
- Drive Minutes
- 74
- Nearby Towns
- Gertrude, Magruder, Summertown, Midville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Colemans Lake and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Colemans Lake?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.emanuelco-ga.gov/148/Building-Inspection-Code-Enforcement (2026)
- https://www.emanuelco-ga.gov/419/Building-Permit-Application (2026)
- https://www.emanuelco-ga.gov/FAQ.aspx?QID=142 ("Structures exceeding 200 square feet require permits, including garages, pole barns, storage buildings, and sheds"; fences under 6 ft and retaining walls under 3 ft do not require permits) (2026)
- https://www.emanuelco-ga.gov/FAQ.aspx?QID=142 ("Emanuel County does not have its own county-specific zoning...") (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Emanuel County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Emanuel County (Swainsboro, GA) is inland east-central Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
