Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Nunez can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Emanuel and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process..
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Benton serves Gary, Blun, Modoc and Blundale and other communities around Nunez.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
63
As of 2026 · Source |
Permits & Setbacks in Emanuel County
Emanuel's permitting office, Emanuel County Building Inspection & Code Enforcement Department, sets the accessory-structure line at 200 square feet — build under that and you generally skip the full building-permit process, though a setback of Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Nunez
Metal garage delivery to Nunez can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Emanuel County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Emanuel County Building Inspection & Code Enforcement Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Do I need a permit for a metal garage in Nunez?
That depends on the garage and the requirements of Emanuel County Building Inspection & Code Enforcement Department. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Nunez, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How far is Benton Metal Depot from Nunez?
Benton Metal Depot's Statesboro location is approximately 46.8 miles from Nunez. The company serves residents throughout Emanuel, including communities such as Gary, Blun, Modoc and Blundale. Current delivery time for a metal garage to the Nunez area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Nunez is Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process., although you should confirm the requirement for your particular property with Emanuel County Building Inspection & Code Enforcement Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Nunez, Emanuel County — At a Glance
- Permit Authority Name
- Emanuel County Building Inspection & Code Enforcement Department
- Permit Authority Url
- https://www.emanuelco-ga.gov/419/Building-Permit-Application
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 46.8
- Drive Minutes
- 63
- Nearby Towns
- Gary, Blun, Modoc, Blundale
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Nunez, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Nunez?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.emanuelco-ga.gov/148/Building-Inspection-Code-Enforcement (2026)
- https://www.emanuelco-ga.gov/419/Building-Permit-Application (2026)
- https://www.emanuelco-ga.gov/FAQ.aspx?QID=142 ("Structures exceeding 200 square feet require permits, including garages, pole barns, storage buildings, and sheds"; fences under 6 ft and retaining walls under 3 ft do not require permits) (2026)
- https://www.emanuelco-ga.gov/FAQ.aspx?QID=142 ("Emanuel County does not have its own county-specific zoning...") (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Emanuel County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Emanuel County (Swainsboro, GA) is inland east-central Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
