Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Stillmore and across Emanuel, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 32.4 miles from Stillmore.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Stillmore is currently estimated at 1 to 2 weeks.
- ◦In Stillmore, a building permit is required once the garage exceeds 200 square feet.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
50
As of 2026 · Source |
Permits & Setbacks in Emanuel County
Emanuel's permitting office, Emanuel County Building Inspection & Code Enforcement Department, sets the accessory-structure line at 200 square feet — build under that and you generally skip the full building-permit process, though a setback of Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Stillmore
Current delivery time to Stillmore is approximately 1 to 2 weeks. Benton also serves nearby communities including Lexsy, Durdenville, Lombard and Canoochee. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Emanuel County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How far is Benton Metal Depot from Stillmore?
Benton Metal Depot's Statesboro location is approximately 32.4 miles from Stillmore. The company serves residents throughout Emanuel, including communities such as Lexsy, Durdenville, Lombard and Canoochee. Current delivery time for a metal garage to the Stillmore area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Stillmore is Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process., although you should confirm the requirement for your particular property with Emanuel County Building Inspection & Code Enforcement Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Emanuel County Building Inspection & Code Enforcement Department has requirements that can affect garage placement, including a current setback of Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Stillmore before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Stillmore?
Current delivery time to Stillmore is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Definitions
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
Stillmore, Emanuel County — At a Glance
- Permit Authority Name
- Emanuel County Building Inspection & Code Enforcement Department
- Permit Authority Url
- https://www.emanuelco-ga.gov/419/Building-Permit-Application
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Emanuel County has no county-specific zoning ordinance (it is one of the few Georgia counties without local zoning restrictions), so no specific side/rear foot figures for accessory structures exist. Needs direct confirmation with the county on what, if any, minimum separation it enforces via the building permit process.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 32.4
- Drive Minutes
- 50
- Nearby Towns
- Lexsy, Durdenville, Lombard, Canoochee
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Stillmore and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Stillmore?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.emanuelco-ga.gov/148/Building-Inspection-Code-Enforcement (2026)
- https://www.emanuelco-ga.gov/419/Building-Permit-Application (2026)
- https://www.emanuelco-ga.gov/FAQ.aspx?QID=142 ("Structures exceeding 200 square feet require permits, including garages, pole barns, storage buildings, and sheds"; fences under 6 ft and retaining walls under 3 ft do not require permits) (2026)
- https://www.emanuelco-ga.gov/FAQ.aspx?QID=142 ("Emanuel County does not have its own county-specific zoning...") (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Emanuel County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Emanuel County (Swainsboro, GA) is inland east-central Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
