Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Daniels can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Evans and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Benton Metal Depot is approximately 38.1 miles from Daniels.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Delivery to Daniels is currently estimated at 1 to 2 weeks.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
No explicit sqft exemption published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Evans County has one. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no Evans County zoning ordinance or accessory-structure setback table was locatable online (no Municode/Zoneomics entry found). Needs direct confirmation with the county.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
64
As of 2026 · Source |
Permits & Setbacks in Evans County
Evans's permitting office, Evans County Code Enforcement (permit/building services), Claxton, GA, sets the accessory-structure line at No explicit sqft exemption published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Evans County has one. Needs direct county contact. square feet — build under that and you generally skip the full building-permit process, though a setback of Not found — no Evans County zoning ordinance or accessory-structure setback table was locatable online (no Municode/Zoneomics entry found). Needs direct confirmation with the county. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Daniels
The current estimate for getting a metal garage to Daniels is 1 to 2 weeks. The area is about 38.1 miles (64 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Evans County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Daniels before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Daniels?
Current delivery time to Daniels is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Evans County Code Enforcement (permit/building services), Claxton, GA has requirements that can affect garage placement, including a current setback of Not found — no Evans County zoning ordinance or accessory-structure setback table was locatable online (no Municode/Zoneomics entry found). Needs direct confirmation with the county.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
How far is Benton Metal Depot from Daniels?
Benton Metal Depot's Statesboro location is approximately 38.1 miles from Daniels. The company serves residents throughout Evans, including communities such as Hughland, Altamaha, Reidsville and Manassas. Current delivery time for a metal garage to the Daniels area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Daniels is Not found — no Evans County zoning ordinance or accessory-structure setback table was locatable online (no Municode/Zoneomics entry found). Needs direct confirmation with the county., although you should confirm the requirement for your particular property with Evans County Code Enforcement (permit/building services), Claxton, GA. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
Daniels, Evans County — At a Glance
- Permit Authority Name
- Evans County Code Enforcement (permit/building services), Claxton, GA
- Permit Authority Url
- https://evanscounty.org/departments/code-enforcement/
- Permit Threshold Sqft
- No explicit sqft exemption published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Evans County has one. Needs direct county contact.
- Setback Feet Side Rear
- Not found — no Evans County zoning ordinance or accessory-structure setback table was locatable online (no Municode/Zoneomics entry found). Needs direct confirmation with the county.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 38.1
- Drive Minutes
- 64
- Nearby Towns
- Hughland, Altamaha, Reidsville, Manassas
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Daniels and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Daniels?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://evanscounty.org/departments/code-enforcement/ (2026)
- Georgia adoption of 2024 IRC with GA Amendments (statewide baseline); no Evans County-specific threshold located online (2026)
- No primary or secondary source located for Evans County setbacks (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Evans County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Evans County is inland (Claxton), roughly 40+ miles from the coast, and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
