Reviewed by the Benton Metal Depot team · Updated
For some residents in Edna, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Evans, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 21.4 miles from Edna.
- ◦Delivery to Edna is currently estimated at 1 to 2 weeks.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
No explicit sqft exemption published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Evans County has one. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no Evans County zoning ordinance or accessory-structure setback table was locatable online (no Municode/Zoneomics entry found). Needs direct confirmation with the county.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
33
As of 2026 · Source |
Permits & Setbacks in Evans County
The permit question for a Edna metal garage comes down to one number from Evans County Code Enforcement (permit/building services), Claxton, GA: No explicit sqft exemption published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Evans County has one. Needs direct county contact. square feet. Stay under it and skip the full permit process; either way, keep the Not found — no Evans County zoning ordinance or accessory-structure setback table was locatable online (no Municode/Zoneomics entry found). Needs direct confirmation with the county. setback in mind before you pick a spot.
Delivery to Edna
Current delivery time to Edna is approximately 1 to 2 weeks. Benton also serves nearby communities including Undine, Jennie, Bellville and Hagan. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Evans County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Do I need a permit for a metal garage in Edna?
That depends on the garage and the requirements of Evans County Code Enforcement (permit/building services), Claxton, GA. The current rule requires a permit once the garage exceeds No explicit sqft exemption published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Evans County has one. Needs direct county contact. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Edna, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Evans County Code Enforcement (permit/building services), Claxton, GA. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How far is Benton Metal Depot from Edna?
Benton Metal Depot's Statesboro location is approximately 21.4 miles from Edna. The company serves residents throughout Evans, including communities such as Undine, Jennie, Bellville and Hagan. Current delivery time for a metal garage to the Edna area is about 1 to 2 weeks.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
Edna, Evans County — At a Glance
- Permit Authority Name
- Evans County Code Enforcement (permit/building services), Claxton, GA
- Permit Authority Url
- https://evanscounty.org/departments/code-enforcement/
- Permit Threshold Sqft
- No explicit sqft exemption published on the county site. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Evans County has one. Needs direct county contact.
- Setback Feet Side Rear
- Not found — no Evans County zoning ordinance or accessory-structure setback table was locatable online (no Municode/Zoneomics entry found). Needs direct confirmation with the county.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 21.4
- Drive Minutes
- 33
- Nearby Towns
- Undine, Jennie, Bellville, Hagan
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Edna and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Edna?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://evanscounty.org/departments/code-enforcement/ (2026)
- Georgia adoption of 2024 IRC with GA Amendments (statewide baseline); no Evans County-specific threshold located online (2026)
- No primary or secondary source located for Evans County setbacks (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Evans County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Evans County is inland (Claxton), roughly 40+ miles from the coast, and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
