Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Birdsville, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Jenkins and the surrounding area.
Key Points
- ◦Benton Metal Depot is approximately 29.9 miles from Birdsville.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Delivery to Birdsville is currently estimated at 1 to 2 weeks.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on the ASCE 7 edition Jenkins County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
39
As of 2026 · Source |
Permits & Setbacks in Jenkins County
Jenkins's permitting office, Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration), sets the accessory-structure line at Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet — build under that and you generally skip the full building-permit process, though a setback of Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Birdsville
The current estimate for getting a metal garage to Birdsville is 1 to 2 weeks. The area is about 29.9 miles (39 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Jenkins County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How long does it take to get a metal garage delivered to Birdsville?
Current delivery time to Birdsville is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Birdsville before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Birdsville, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How close can my metal garage be to the property line?
The current setback in Birdsville is Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact., although you should confirm the requirement for your particular property with Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Birdsville?
Benton Metal Depot's Statesboro location is approximately 29.9 miles from Birdsville. The company serves residents throughout Jenkins, including communities such as Rogers, Lawton, Scarboro and Paramore Hill. Current delivery time for a metal garage to the Birdsville area is about 1 to 2 weeks.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
Birdsville, Jenkins County — At a Glance
- Permit Authority Name
- Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration)
- Permit Authority Url
- https://www.jenkinscountyga.com/jenkins-county-administration.php
- Permit Threshold Sqft
- Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact.
- Setback Feet Side Rear
- Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on the ASCE 7 edition Jenkins County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 29.9
- Drive Minutes
- 39
- Nearby Towns
- Rogers, Lawton, Scarboro, Paramore Hill
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Birdsville and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Birdsville?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.jenkinscountyga.com/jenkins-county-administration.php — needs direct confirmation by phone (478-982-2563 / 478-982-4683) (2026)
- https://www.jenkinscountyga.com/jenkins-county-administration.php (2026)
- General GA IRC baseline exemption (120 sq ft) — no Jenkins County-specific page found (2026)
- Not found (2026)
- General ASCE 7 inland-Georgia range (aggregated from windload.solutions and similar secondary sources) — no county-specific or primary map source found (2026)
- Given/client spec — Jenkins County is inland Georgia (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
