Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Butts and across Jenkins, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact..
- ◦Benton serves Rogers, Lawton, Scarboro and Paramore Hill and other communities around Butts.
- ◦In Butts, a building permit is required once the garage exceeds Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet.
At a Glance
| Permit threshold |
Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on the ASCE 7 edition Jenkins County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
39
As of 2026 · Source |
Permits & Setbacks in Jenkins County
The permit question for a Butts metal garage comes down to one number from Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration): Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet. Stay under it and skip the full permit process; either way, keep the Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact. setback in mind before you pick a spot.
Delivery to Butts
Current delivery time to Butts is approximately 1 to 2 weeks. Benton also serves nearby communities including Rogers, Lawton, Scarboro and Paramore Hill. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Jenkins County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Butts, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Do I need a permit for a metal garage in Butts?
That depends on the garage and the requirements of Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration). The current rule requires a permit once the garage exceeds Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Butts before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
How long does it take to get a metal garage delivered to Butts?
Current delivery time to Butts is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Definitions
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
Butts, Jenkins County — At a Glance
- Permit Authority Name
- Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration)
- Permit Authority Url
- https://www.jenkinscountyga.com/jenkins-county-administration.php
- Permit Threshold Sqft
- Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact.
- Setback Feet Side Rear
- Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on the ASCE 7 edition Jenkins County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 29.9
- Drive Minutes
- 39
- Nearby Towns
- Rogers, Lawton, Scarboro, Paramore Hill
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Butts, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Butts?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.jenkinscountyga.com/jenkins-county-administration.php — needs direct confirmation by phone (478-982-2563 / 478-982-4683) (2026)
- https://www.jenkinscountyga.com/jenkins-county-administration.php (2026)
- General GA IRC baseline exemption (120 sq ft) — no Jenkins County-specific page found (2026)
- Not found (2026)
- General ASCE 7 inland-Georgia range (aggregated from windload.solutions and similar secondary sources) — no county-specific or primary map source found (2026)
- Given/client spec — Jenkins County is inland Georgia (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
