Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Rogers and across Jenkins, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦In Rogers, a building permit is required once the garage exceeds Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet.
- ◦Benton serves Lawton, Scarboro, Paramore Hill and Birdsville and other communities around Rogers.
- ◦The current local setback for a metal garage is Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on the ASCE 7 edition Jenkins County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
39
As of 2026 · Source |
Permits & Setbacks in Jenkins County
The permit question for a Rogers metal garage comes down to one number from Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration): Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet. Stay under it and skip the full permit process; either way, keep the Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact. setback in mind before you pick a spot.
Delivery to Rogers
The current estimate for getting a metal garage to Rogers is 1 to 2 weeks. The area is about 29.9 miles (39 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Jenkins County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration) has requirements that can affect garage placement, including a current setback of Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Do I need a permit for a metal garage in Rogers?
That depends on the garage and the requirements of Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration). The current rule requires a permit once the garage exceeds Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How far is Benton Metal Depot from Rogers?
Benton Metal Depot's Statesboro location is approximately 29.9 miles from Rogers. The company serves residents throughout Jenkins, including communities such as Lawton, Scarboro, Paramore Hill and Birdsville. Current delivery time for a metal garage to the Rogers area is about 1 to 2 weeks.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
Rogers, Jenkins County — At a Glance
- Permit Authority Name
- Jenkins County Administration / Clerk's Office (no dedicated stand-alone building-permit department page was found; permitting appears to be handled through county administration)
- Permit Authority Url
- https://www.jenkinscountyga.com/jenkins-county-administration.php
- Permit Threshold Sqft
- Not found — Jenkins County does not appear to publish a dedicated accessory-structure permit page online. Georgia's state minimum code baseline (IRC) generally exempts one-story detached sheds/playhouses up to 120 sq ft, but whether Jenkins County has adopted/enforces that as-is is unconfirmed. Needs direct county contact.
- Setback Feet Side Rear
- Not found — no Jenkins County zoning ordinance setback table for accessory structures was located online. Needs direct county contact.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; the exact design wind speed depends on the ASCE 7 edition Jenkins County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 29.9
- Drive Minutes
- 39
- Nearby Towns
- Lawton, Scarboro, Paramore Hill, Birdsville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Rogers, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Rogers?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.jenkinscountyga.com/jenkins-county-administration.php — needs direct confirmation by phone (478-982-2563 / 478-982-4683) (2026)
- https://www.jenkinscountyga.com/jenkins-county-administration.php (2026)
- General GA IRC baseline exemption (120 sq ft) — no Jenkins County-specific page found (2026)
- Not found (2026)
- General ASCE 7 inland-Georgia range (aggregated from windload.solutions and similar secondary sources) — no county-specific or primary map source found (2026)
- Given/client spec — Jenkins County is inland Georgia (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
