Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Allenhurst, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Liberty and the surrounding area.
Key Points
- ◦The current local setback for a metal garage is Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦In Allenhurst, a building permit is required once the garage exceeds No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet.
- ◦Benton serves Walthourville, Creek Island, Gumbranch and Flemington and other communities around Allenhurst.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
At a Glance
| Permit threshold |
No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Liberty County in Wind Zone 2. Secondary sources put ASCE 7 ultimate design wind speeds for coastal GA counties like Liberty in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and distance from the coast, and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
94
As of 2026 · Source |
Permits & Setbacks in Liberty County
The permit question for a Allenhurst metal garage comes down to one number from Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections): No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet. Stay under it and skip the full permit process; either way, keep the Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF. setback in mind before you pick a spot.
Delivery to Allenhurst
Current delivery time to Allenhurst is approximately 1 to 2 weeks. Benton also serves nearby communities including Walthourville, Creek Island, Gumbranch and Flemington. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Liberty County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How far is Benton Metal Depot from Allenhurst?
Benton Metal Depot's Statesboro location is approximately 57.3 miles from Allenhurst. The company serves residents throughout Liberty, including communities such as Walthourville, Creek Island, Gumbranch and Flemington. Current delivery time for a metal garage to the Allenhurst area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Allenhurst is Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF., although you should confirm the requirement for your particular property with Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Allenhurst, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Allenhurst before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Allenhurst?
Current delivery time to Allenhurst is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Allenhurst?
That depends on the garage and the requirements of Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections). The current rule requires a permit once the garage exceeds No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Definitions
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
Allenhurst, Liberty County — At a Glance
- Permit Authority Name
- Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections)
- Permit Authority Url
- https://www.libertycountyga.gov/211/Building-Licensing
- Permit Threshold Sqft
- No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation.
- Setback Feet Side Rear
- Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF.
- Wind Load Zone
- Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Liberty County in Wind Zone 2. Secondary sources put ASCE 7 ultimate design wind speeds for coastal GA counties like Liberty in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and distance from the coast, and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 57.3
- Drive Minutes
- 94
- Nearby Towns
- Walthourville, Creek Island, Gumbranch, Flemington
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Allenhurst, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Allenhurst?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.libertycountyga.gov/211/Building-Licensing (2026)
- Georgia adoption of 2024 IRC with GA Amendments (statewide baseline); Liberty County UDO referenced at https://thelcpc.org/zoning/ — specific threshold not located in accessible text (2026)
- Liberty County Unified Development Ordinance (LCPC), referenced at https://thelcpc.org/zoning/ — primary PDF needs direct retrieval/verification (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (primary: lists Liberty among the 6 GA Wind Zone 2 coastal counties) — mph range aggregated from homenation.com/blog/complete-guide-to-georgia-wind-zones and windload.solutions (2026)
- Given/client spec — Liberty County is a coastal Georgia county; confirmed independently by its Wind Zone 2 listing at https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
