Reviewed by the Benton Metal Depot team · Updated
For some residents in Sunbury, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Liberty, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF..
- ◦Benton serves Limerick, Screven Fork, Halfmoon Landing and Seabrook and other communities around Sunbury.
- ◦In Sunbury, a building permit is required once the garage exceeds No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet.
At a Glance
| Permit threshold |
No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Liberty County in Wind Zone 2. Secondary sources put ASCE 7 ultimate design wind speeds for coastal GA counties like Liberty in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and distance from the coast, and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
84
As of 2026 · Source |
Permits & Setbacks in Liberty County
Liberty's permitting office, Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections), sets the accessory-structure line at No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet — build under that and you generally skip the full building-permit process, though a setback of Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Sunbury
Current delivery time to Sunbury is approximately 1 to 2 weeks. Benton also serves nearby communities including Limerick, Screven Fork, Halfmoon Landing and Seabrook. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Liberty County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Sunbury before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Sunbury?
Current delivery time to Sunbury is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections) has requirements that can affect garage placement, including a current setback of Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How far is Benton Metal Depot from Sunbury?
Benton Metal Depot's Statesboro location is approximately 68.9 miles from Sunbury. The company serves residents throughout Liberty, including communities such as Limerick, Screven Fork, Halfmoon Landing and Seabrook. Current delivery time for a metal garage to the Sunbury area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Sunbury is Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF., although you should confirm the requirement for your particular property with Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
Sunbury, Liberty County — At a Glance
- Permit Authority Name
- Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections)
- Permit Authority Url
- https://www.libertycountyga.gov/211/Building-Licensing
- Permit Threshold Sqft
- No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation.
- Setback Feet Side Rear
- Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF.
- Wind Load Zone
- Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Liberty County in Wind Zone 2. Secondary sources put ASCE 7 ultimate design wind speeds for coastal GA counties like Liberty in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and distance from the coast, and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 68.9
- Drive Minutes
- 84
- Nearby Towns
- Limerick, Screven Fork, Halfmoon Landing, Seabrook
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Sunbury and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Sunbury?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.libertycountyga.gov/211/Building-Licensing (2026)
- Georgia adoption of 2024 IRC with GA Amendments (statewide baseline); Liberty County UDO referenced at https://thelcpc.org/zoning/ — specific threshold not located in accessible text (2026)
- Liberty County Unified Development Ordinance (LCPC), referenced at https://thelcpc.org/zoning/ — primary PDF needs direct retrieval/verification (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (primary: lists Liberty among the 6 GA Wind Zone 2 coastal counties) — mph range aggregated from homenation.com/blog/complete-guide-to-georgia-wind-zones and windload.solutions (2026)
- Given/client spec — Liberty County is a coastal Georgia county; confirmed independently by its Wind Zone 2 listing at https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
