Metal Garages in Gumbranch 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Gumbranch and across Liberty, with different building sizes depending on the amount of space the property owner needs.

Key Points

◦In Gumbranch, a building permit is required once the garage exceeds No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet.
◦Benton serves Creek Island, Flemington, Hinesville and Trinity and other communities around Gumbranch.
◦Check the permit and setback rules before deciding exactly where the garage will go.
◦The current local setback for a metal garage is Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF..
◦Plan for door clearance and walking room when deciding how wide your garage needs to be.

At a Glance

Permit threshold	No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. As of 2026 · Source
Setback (side/rear)	Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF. As of 2026 · Source
Wind load zone	Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Liberty County in Wind Zone 2. Secondary sources put ASCE 7 ultimate design wind speeds for coastal GA counties like Liberty in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and distance from the coast, and must be confirmed with a GA-licensed engineer or the county building official before publishing. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	81 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Liberty County

Liberty treats a metal garage like any other accessory structure: under No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet, Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections) typically doesn't require a full permit, but the Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF. setback rule still governs where it can sit on the lot.

Delivery to Gumbranch

The current estimate for getting a metal garage to Gumbranch is 1 to 2 weeks. The area is about 50.6 miles (81 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.

Representative product photo — a Liberty County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Do I need a permit for a metal garage in Gumbranch?

That depends on the garage and the requirements of Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections). The current rule requires a permit once the garage exceeds No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Gumbranch, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

How close can my metal garage be to the property line?

The current setback in Gumbranch is Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF., although you should confirm the requirement for your particular property with Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

Definitions

◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.
◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.
◦ Roof Pitch: How steep the roof is, usually described by how much it rises over a set horizontal distance.
◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.
◦ Wall Panel: Formed metal sheet used to enclose and protect the exterior walls of the garage.
◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.

Gumbranch, Liberty County — At a Glance

Permit Authority Name: Liberty County Building & Licensing Department (issues permits for unincorporated Liberty County except the City of Hinesville, which has its own Department of Inspections)
Permit Authority Url: https://www.libertycountyga.gov/211/Building-Licensing
Permit Threshold Sqft: No explicit sqft exemption found published on the county page. Georgia's statewide 2024 IRC baseline exempts one-story detached accessory structures ≤200 sq ft (Section R105.2) absent a stricter local amendment — not confirmed whether Liberty County/the Liberty Consolidated Planning Commission (LCPC) has one. Needs direct confirmation.
Setback Feet Side Rear: Not independently pulled from a district-by-district table — Liberty County's Unified Development Ordinance (administered by the LCPC) sets zoning-district dimensional standards including accessory-structure setbacks, but the specific side/rear foot figures need to be pulled from the primary UDO PDF.
Wind Load Zone: Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Liberty County in Wind Zone 2. Secondary sources put ASCE 7 ultimate design wind speeds for coastal GA counties like Liberty in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and distance from the coast, and must be confirmed with a GA-licensed engineer or the county building official before publishing.
Coastal: 1
Drive Miles: 50.6
Drive Minutes: 81
Nearby Towns: Creek Island, Flemington, Hinesville, Trinity
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Gumbranch, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.

Ready to talk through your metal garages project in Gumbranch?

Call (912) 489-5795

Sources

Other Cities We Serve in Liberty County

See the Liberty County hub for metal garages

Allenhurst Creek Island Crossroads Dorchester Fleming Flemington Fort Stewart Gumbranch Halfmoon Landing Hinesville Lecount Limerick McIntosh Midway Retreat Riceboro Screven Fork Seabrook Sunbury Trinity Walthourville Willie

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Gumbranch, Liberty County, Georgia (2026)