Reviewed by the Benton Metal Depot team · Updated
For some residents in Bethera, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Berkeley, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦The current local setback for a metal garage is Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦In Bethera, a building permit is required once the garage exceeds 200 square feet.
- ◦Benton serves Witherbee, Limerick, Richmond and Cordesville and other communities around Bethera.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number.
As of 2026 · Source |
| Wind load zone |
Berkeley County design criteria require a minimum of 133 mph wind design ("D" seismic for commercial, "D-2" for residential"), per the county's own building-regulations documentation — a real, county-published figure rather than a generic estimate, but still confirm which code edition/map this is tied to (and whether it applies county-wide or only near the coastal/Charleston-adjacent portion of the county) with a licensed SC engineer or the county building official before treating it as final.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
237
As of 2026 · Source |
Permits & Setbacks in Berkeley County
Berkeley treats a metal garage like any other accessory structure: under 200 square feet, Berkeley County Building and Codes Enforcement typically doesn't require a full permit, but the Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number. setback rule still governs where it can sit on the lot.
Delivery to Bethera
The current estimate for getting a metal garage to Bethera is 1 to 2 weeks. The area is about 176.7 miles (237 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Berkeley County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Bethera before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Bethera?
Current delivery time to Bethera is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Berkeley County Building and Codes Enforcement has requirements that can affect garage placement, including a current setback of Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How far is Benton Metal Depot from Bethera?
Benton Metal Depot's Statesboro location is approximately 176.7 miles from Bethera. The company serves residents throughout Berkeley, including communities such as Witherbee, Limerick, Richmond and Cordesville. Current delivery time for a metal garage to the Bethera area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Bethera is Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number., although you should confirm the requirement for your particular property with Berkeley County Building and Codes Enforcement. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
Bethera, Berkeley County — At a Glance
- Permit Authority Name
- Berkeley County Building and Codes Enforcement
- Permit Authority Url
- https://berkeleycountysc.gov/dept/codes/
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number.
- Wind Load Zone
- Berkeley County design criteria require a minimum of 133 mph wind design ("D" seismic for commercial, "D-2" for residential"), per the county's own building-regulations documentation — a real, county-published figure rather than a generic estimate, but still confirm which code edition/map this is tied to (and whether it applies county-wide or only near the coastal/Charleston-adjacent portion of the county) with a licensed SC engineer or the county building official before treating it as final.
- Coastal
- Drive Miles
- 176.7
- Drive Minutes
- 237
- Nearby Towns
- Witherbee, Limerick, Richmond, Cordesville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Bethera and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Bethera?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://berkeleycountysc.gov/dept/codes/ (2026)
- South Carolina Residential Code § R105.2 (2018 IRC, adopted statewide) — same statewide default as neighboring Dorchester/Aiken counties; not independently re-confirmed on a Berkeley County-specific page in this pass, so verify against Berkeley County's current permit application guidance before publishing (2026)
- https://berkeleycountysc.gov/wp-content/uploads/docs/Buildings-and-Building-Regulations.pdf (not independently readable as text in this pass) and https://library.municode.com/sc/berkeley_county/codes/code_of_ordinances?nodeId=COOR_CH11BUBURE (2026)
- https://berkeleycountysc.gov/wp-content/uploads/docs/Buildings-and-Building-Regulations.pdf (2026)
- Berkeley County is not among the coastal counties named in the client spec, though its southeastern portion borders Charleston County/the coast directly (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Berkeley County
See the Berkeley County hub for metal garages
