Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Kittredge? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Berkeley, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 163.6 miles from Kittredge.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Delivery to Kittredge is currently estimated at 1 to 2 weeks.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number.
As of 2026 · Source |
| Wind load zone |
Berkeley County design criteria require a minimum of 133 mph wind design ("D" seismic for commercial, "D-2" for residential"), per the county's own building-regulations documentation — a real, county-published figure rather than a generic estimate, but still confirm which code edition/map this is tied to (and whether it applies county-wide or only near the coastal/Charleston-adjacent portion of the county) with a licensed SC engineer or the county building official before treating it as final.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
209
As of 2026 · Source |
Permits & Setbacks in Berkeley County
Before a metal garage goes up in Kittredge, check with Berkeley County Building and Codes Enforcement — Berkeley's cutoff for requiring a building permit is 200 square feet. Below that, you still need to clear the Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number. setback from your property line.
Delivery to Kittredge
Metal garage delivery to Kittredge can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Berkeley County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Berkeley County Building and Codes Enforcement. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How close can my metal garage be to the property line?
The current setback in Kittredge is Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number., although you should confirm the requirement for your particular property with Berkeley County Building and Codes Enforcement. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Kittredge?
Benton Metal Depot's Statesboro location is approximately 163.6 miles from Kittredge. The company serves residents throughout Berkeley, including communities such as Simpson Crossing, Old Cordesville, Ellwood and Whitesville. Current delivery time for a metal garage to the Kittredge area is about 1 to 2 weeks.
How long does it take to get a metal garage delivered to Kittredge?
Current delivery time to Kittredge is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Kittredge before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Kittredge, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Berkeley County Building and Codes Enforcement has requirements that can affect garage placement, including a current setback of Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
Kittredge, Berkeley County — At a Glance
- Permit Authority Name
- Berkeley County Building and Codes Enforcement
- Permit Authority Url
- https://berkeleycountysc.gov/dept/codes/
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number.
- Wind Load Zone
- Berkeley County design criteria require a minimum of 133 mph wind design ("D" seismic for commercial, "D-2" for residential"), per the county's own building-regulations documentation — a real, county-published figure rather than a generic estimate, but still confirm which code edition/map this is tied to (and whether it applies county-wide or only near the coastal/Charleston-adjacent portion of the county) with a licensed SC engineer or the county building official before treating it as final.
- Coastal
- Drive Miles
- 163.6
- Drive Minutes
- 209
- Nearby Towns
- Simpson Crossing, Old Cordesville, Ellwood, Whitesville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Kittredge, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Kittredge?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://berkeleycountysc.gov/dept/codes/ (2026)
- South Carolina Residential Code § R105.2 (2018 IRC, adopted statewide) — same statewide default as neighboring Dorchester/Aiken counties; not independently re-confirmed on a Berkeley County-specific page in this pass, so verify against Berkeley County's current permit application guidance before publishing (2026)
- https://berkeleycountysc.gov/wp-content/uploads/docs/Buildings-and-Building-Regulations.pdf (not independently readable as text in this pass) and https://library.municode.com/sc/berkeley_county/codes/code_of_ordinances?nodeId=COOR_CH11BUBURE (2026)
- https://berkeleycountysc.gov/wp-content/uploads/docs/Buildings-and-Building-Regulations.pdf (2026)
- Berkeley County is not among the coastal counties named in the client spec, though its southeastern portion borders Charleston County/the coast directly (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Berkeley County
See the Berkeley County hub for metal garages
