Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Moreland and across Berkeley, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Benton Metal Depot is approximately 178.7 miles from Moreland.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Delivery to Moreland is currently estimated at 1 to 2 weeks.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number.
As of 2026 · Source |
| Wind load zone |
Berkeley County design criteria require a minimum of 133 mph wind design ("D" seismic for commercial, "D-2" for residential"), per the county's own building-regulations documentation — a real, county-published figure rather than a generic estimate, but still confirm which code edition/map this is tied to (and whether it applies county-wide or only near the coastal/Charleston-adjacent portion of the county) with a licensed SC engineer or the county building official before treating it as final.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
232
As of 2026 · Source |
Permits & Setbacks in Berkeley County
Before a metal garage goes up in Moreland, check with Berkeley County Building and Codes Enforcement — Berkeley's cutoff for requiring a building permit is 200 square feet. Below that, you still need to clear the Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number. setback from your property line.
Delivery to Moreland
Metal garage delivery to Moreland can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Berkeley County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Moreland before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Moreland?
Current delivery time to Moreland is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Moreland, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Berkeley County Building and Codes Enforcement. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How far is Benton Metal Depot from Moreland?
Benton Metal Depot's Statesboro location is approximately 178.7 miles from Moreland. The company serves residents throughout Berkeley, including communities such as Huger, Hagan, Woodland and Old Joe. Current delivery time for a metal garage to the Moreland area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Moreland is Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number., although you should confirm the requirement for your particular property with Berkeley County Building and Codes Enforcement. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Moreland, Berkeley County — At a Glance
- Permit Authority Name
- Berkeley County Building and Codes Enforcement
- Permit Authority Url
- https://berkeleycountysc.gov/dept/codes/
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not confirmed. A search result appeared to describe a "within 3 ft of the main building counts as part of the main building for setback purposes" rule, but that language traces to the City of Berkeley, California's municipal code, not Berkeley County, SC — it was NOT used here to avoid misattributing a fact to the wrong jurisdiction. Berkeley County SC's own accessory-structure setback table needs direct primary-source lookup before publishing any number.
- Wind Load Zone
- Berkeley County design criteria require a minimum of 133 mph wind design ("D" seismic for commercial, "D-2" for residential"), per the county's own building-regulations documentation — a real, county-published figure rather than a generic estimate, but still confirm which code edition/map this is tied to (and whether it applies county-wide or only near the coastal/Charleston-adjacent portion of the county) with a licensed SC engineer or the county building official before treating it as final.
- Coastal
- Drive Miles
- 178.7
- Drive Minutes
- 232
- Nearby Towns
- Huger, Hagan, Woodland, Old Joe
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Moreland and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Moreland?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://berkeleycountysc.gov/dept/codes/ (2026)
- South Carolina Residential Code § R105.2 (2018 IRC, adopted statewide) — same statewide default as neighboring Dorchester/Aiken counties; not independently re-confirmed on a Berkeley County-specific page in this pass, so verify against Berkeley County's current permit application guidance before publishing (2026)
- https://berkeleycountysc.gov/wp-content/uploads/docs/Buildings-and-Building-Regulations.pdf (not independently readable as text in this pass) and https://library.municode.com/sc/berkeley_county/codes/code_of_ordinances?nodeId=COOR_CH11BUBURE (2026)
- https://berkeleycountysc.gov/wp-content/uploads/docs/Buildings-and-Building-Regulations.pdf (2026)
- Berkeley County is not among the coastal counties named in the client spec, though its southeastern portion borders Charleston County/the coast directly (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Berkeley County
See the Berkeley County hub for metal garages
