Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Cordova? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Orangeburg, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Benton serves Rowesville, Haddock, Felder and Gravel Hill and other communities around Cordova.
- ◦In Cordova, a building permit is required once the garage exceeds 200 square feet.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦The current local setback for a metal garage is Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts..
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts.
As of 2026 · Source |
| Wind load zone |
Inland South Carolina (Midlands) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
134
As of 2026 · Source |
Permits & Setbacks in Orangeburg County
Before a metal garage goes up in Cordova, check with Orangeburg County Permitting and Inspections Department (Planning & Community Development) — Orangeburg's cutoff for requiring a building permit is 200 square feet. Below that, you still need to clear the Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts. setback from your property line.
Delivery to Cordova
The current estimate for getting a metal garage to Cordova is 1 to 2 weeks. The area is about 99.3 miles (134 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Orangeburg County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Do I need a permit for a metal garage in Cordova?
That depends on the garage and the requirements of Orangeburg County Permitting and Inspections Department (Planning & Community Development). The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Cordova, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Orangeburg County Permitting and Inspections Department (Planning & Community Development). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
How far is Benton Metal Depot from Cordova?
Benton Metal Depot's Statesboro location is approximately 99.3 miles from Cordova. The company serves residents throughout Orangeburg, including communities such as Rowesville, Haddock, Felder and Gravel Hill. Current delivery time for a metal garage to the Cordova area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Cordova is Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts., although you should confirm the requirement for your particular property with Orangeburg County Permitting and Inspections Department (Planning & Community Development). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
Cordova, Orangeburg County — At a Glance
- Permit Authority Name
- Orangeburg County Permitting and Inspections Department (Planning & Community Development)
- Permit Authority Url
- https://www.orangeburgcounty.org/223/Permits-Inspections
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts.
- Wind Load Zone
- Inland South Carolina (Midlands) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 99.3
- Drive Minutes
- 134
- Nearby Towns
- Rowesville, Haddock, Felder, Gravel Hill
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Cordova and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Cordova?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.orangeburgcounty.org/223/Permits-Inspections (2026)
- Orangeburg County FAQ (https://www.orangeburgcounty.org/m/faq?cat=25#question-126) — one-story detached storage structures accessory to a one- or two-family dwelling are exempt from a permit if floor area does not exceed 200 sq ft; verify against the primary building-regs PDF at https://www.orangeburgcounty.org/DocumentCenter/View/437/Planning-Buildings-and-Building-Regulations-PDF (2026)
- https://library.municode.com/sc/orangeburg_county/codes/code_of_ordinances?nodeId=COOR_APXAZO — needs direct lookup of the district yard-requirement table (2026)
- General ASCE 7 inland-SC range (windload.solutions and similar secondary sources) — no county-specific primary map source found (2026)
- Orangeburg County is inland SC, not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Orangeburg County
See the Orangeburg County hub for metal garages
