Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Neeses, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Orangeburg and the surrounding area.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦The current local setback for a metal garage is Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦In Neeses, a building permit is required once the garage exceeds 200 square feet.
- ◦Benton serves Bolen Town, Livingston, Norway and Wolfton and other communities around Neeses.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts.
As of 2026 · Source |
| Wind load zone |
Inland South Carolina (Midlands) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
118
As of 2026 · Source |
Permits & Setbacks in Orangeburg County
The permit question for a Neeses metal garage comes down to one number from Orangeburg County Permitting and Inspections Department (Planning & Community Development): 200 square feet. Stay under it and skip the full permit process; either way, keep the Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts. setback in mind before you pick a spot.
Delivery to Neeses
Residents in Neeses are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 95.8 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Orangeburg County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Orangeburg County Permitting and Inspections Department (Planning & Community Development). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Neeses before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Neeses?
Current delivery time to Neeses is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How far is Benton Metal Depot from Neeses?
Benton Metal Depot's Statesboro location is approximately 95.8 miles from Neeses. The company serves residents throughout Orangeburg, including communities such as Bolen Town, Livingston, Norway and Wolfton. Current delivery time for a metal garage to the Neeses area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Neeses is Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts., although you should confirm the requirement for your particular property with Orangeburg County Permitting and Inspections Department (Planning & Community Development). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Neeses, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Orangeburg County Permitting and Inspections Department (Planning & Community Development) has requirements that can affect garage placement, including a current setback of Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Definitions
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Neeses, Orangeburg County — At a Glance
- Permit Authority Name
- Orangeburg County Permitting and Inspections Department (Planning & Community Development)
- Permit Authority Url
- https://www.orangeburgcounty.org/223/Permits-Inspections
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts.
- Wind Load Zone
- Inland South Carolina (Midlands) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 95.8
- Drive Minutes
- 118
- Nearby Towns
- Bolen Town, Livingston, Norway, Wolfton
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Neeses, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Neeses?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.orangeburgcounty.org/223/Permits-Inspections (2026)
- Orangeburg County FAQ (https://www.orangeburgcounty.org/m/faq?cat=25#question-126) — one-story detached storage structures accessory to a one- or two-family dwelling are exempt from a permit if floor area does not exceed 200 sq ft; verify against the primary building-regs PDF at https://www.orangeburgcounty.org/DocumentCenter/View/437/Planning-Buildings-and-Building-Regulations-PDF (2026)
- https://library.municode.com/sc/orangeburg_county/codes/code_of_ordinances?nodeId=COOR_APXAZO — needs direct lookup of the district yard-requirement table (2026)
- General ASCE 7 inland-SC range (windload.solutions and similar secondary sources) — no county-specific primary map source found (2026)
- Orangeburg County is inland SC, not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Orangeburg County
See the Orangeburg County hub for metal garages
