Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Jamison, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Orangeburg.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦The current local setback for a metal garage is Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦In Jamison, a building permit is required once the garage exceeds 200 square feet.
- ◦Benton serves Stilton, Orangeburg, Haddock and Felder and other communities around Jamison.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts.
As of 2026 · Source |
| Wind load zone |
Inland South Carolina (Midlands) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
141
As of 2026 · Source |
Permits & Setbacks in Orangeburg County
Orangeburg's permitting office, Orangeburg County Permitting and Inspections Department (Planning & Community Development), sets the accessory-structure line at 200 square feet — build under that and you generally skip the full building-permit process, though a setback of Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Jamison
Residents in Jamison are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 107.6 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Orangeburg County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Jamison, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Do I need a permit for a metal garage in Jamison?
That depends on the garage and the requirements of Orangeburg County Permitting and Inspections Department (Planning & Community Development). The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Orangeburg County Permitting and Inspections Department (Planning & Community Development). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How far is Benton Metal Depot from Jamison?
Benton Metal Depot's Statesboro location is approximately 107.6 miles from Jamison. The company serves residents throughout Orangeburg, including communities such as Stilton, Orangeburg, Haddock and Felder. Current delivery time for a metal garage to the Jamison area is about 1 to 2 weeks.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
Jamison, Orangeburg County — At a Glance
- Permit Authority Name
- Orangeburg County Permitting and Inspections Department (Planning & Community Development)
- Permit Authority Url
- https://www.orangeburgcounty.org/223/Permits-Inspections
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not independently confirmed — Orangeburg County zoning ordinance (Municode Appendix A) has district-specific yard tables but the exact side/rear accessory-structure setback figures were not retrievable from search excerpts.
- Wind Load Zone
- Inland South Carolina (Midlands) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 107.6
- Drive Minutes
- 141
- Nearby Towns
- Stilton, Orangeburg, Haddock, Felder
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Jamison and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Jamison?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.orangeburgcounty.org/223/Permits-Inspections (2026)
- Orangeburg County FAQ (https://www.orangeburgcounty.org/m/faq?cat=25#question-126) — one-story detached storage structures accessory to a one- or two-family dwelling are exempt from a permit if floor area does not exceed 200 sq ft; verify against the primary building-regs PDF at https://www.orangeburgcounty.org/DocumentCenter/View/437/Planning-Buildings-and-Building-Regulations-PDF (2026)
- https://library.municode.com/sc/orangeburg_county/codes/code_of_ordinances?nodeId=COOR_APXAZO — needs direct lookup of the district yard-requirement table (2026)
- General ASCE 7 inland-SC range (windload.solutions and similar secondary sources) — no county-specific primary map source found (2026)
- Orangeburg County is inland SC, not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Orangeburg County
See the Orangeburg County hub for metal garages
