Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Fort McAllister, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Bryan.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 59.8 miles from Fort McAllister.
- ◦Delivery to Fort McAllister is currently estimated at 1 to 2 weeks.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦In Fort McAllister, a building permit is required once the garage exceeds 200 square feet.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
78
As of 2026 · Source |
Permits & Setbacks in Bryan County
The permit question for a Fort McAllister metal garage comes down to one number from Bryan County Community Development Department, Building and Codes Division: 200 square feet. Stay under it and skip the full permit process; either way, keep the Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF. setback in mind before you pick a spot.
Delivery to Fort McAllister
The current estimate for getting a metal garage to Fort McAllister is 1 to 2 weeks. The area is about 59.8 miles (78 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Bryan County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Do I need a permit for a metal garage in Fort McAllister?
That depends on the garage and the requirements of Bryan County Community Development Department, Building and Codes Division. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Bryan County Community Development Department, Building and Codes Division has requirements that can affect garage placement, including a current setback of Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Bryan County Community Development Department, Building and Codes Division. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Definitions
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
Fort McAllister, Bryan County — At a Glance
- Permit Authority Name
- Bryan County Community Development Department, Building and Codes Division
- Permit Authority Url
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
- Wind Load Zone
- Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 59.8
- Drive Minutes
- 78
- Nearby Towns
- Fancy Hall, Daniel, Belfast, Oak Level
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Fort McAllister and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Fort McAllister?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes (2026)
- https://www.bryancountyga.gov/government/departments-a-g/community-development/building-and-codes/learn-more ("buildings greater than 200 square feet in size" require a building permit) (2026)
- Bryan County Code of Ordinances Ch. 114, Sec. 114-611, as summarized at https://www.zoneomics.com/code/bryan-county-unincorporated-GA/chapter_6 — verify against primary ordinance at https://library.municode.com/ga/bryan_county (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (primary: lists Bryan among the 6 GA Wind Zone 2 coastal counties: Chatham, Bryan, Liberty, McIntosh, Glynn, Camden) — mph range aggregated from windload.solutions/homenation.com secondary sources (2026)
- Given/client spec — Bryan County is a coastal Georgia county; confirmed independently by its Wind Zone 2 listing at https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
