Reviewed by the Benton Metal Depot team · Updated
For some residents in Groveland, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout Bryan, so the building can be planned around the job it needs to do on your property.
Key Points
- ◦Delivery to Groveland is currently estimated at 1 to 2 weeks.
- ◦Benton Metal Depot is approximately 19.2 miles from Groveland.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
29
As of 2026 · Source |
Permits & Setbacks in Bryan County
Bryan's permitting office, Bryan County Community Development Department, Building and Codes Division, sets the accessory-structure line at 200 square feet — build under that and you generally skip the full building-permit process, though a setback of Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Groveland
Metal garage delivery to Groveland can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Bryan County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Do I need a permit for a metal garage in Groveland?
That depends on the garage and the requirements of Bryan County Community Development Department, Building and Codes Division. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Bryan County Community Development Department, Building and Codes Division. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Groveland, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
How far is Benton Metal Depot from Groveland?
Benton Metal Depot's Statesboro location is approximately 19.2 miles from Groveland. The company serves residents throughout Bryan, including communities such as Nevils, Southward, Lanier and Letford. Current delivery time for a metal garage to the Groveland area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Groveland is Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF., although you should confirm the requirement for your particular property with Bryan County Community Development Department, Building and Codes Division. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
Groveland, Bryan County — At a Glance
- Permit Authority Name
- Bryan County Community Development Department, Building and Codes Division
- Permit Authority Url
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
- Wind Load Zone
- Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 19.2
- Drive Minutes
- 29
- Nearby Towns
- Nevils, Southward, Lanier, Letford
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Groveland, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Groveland?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes (2026)
- https://www.bryancountyga.gov/government/departments-a-g/community-development/building-and-codes/learn-more ("buildings greater than 200 square feet in size" require a building permit) (2026)
- Bryan County Code of Ordinances Ch. 114, Sec. 114-611, as summarized at https://www.zoneomics.com/code/bryan-county-unincorporated-GA/chapter_6 — verify against primary ordinance at https://library.municode.com/ga/bryan_county (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (primary: lists Bryan among the 6 GA Wind Zone 2 coastal counties: Chatham, Bryan, Liberty, McIntosh, Glynn, Camden) — mph range aggregated from windload.solutions/homenation.com secondary sources (2026)
- Given/client spec — Bryan County is a coastal Georgia county; confirmed independently by its Wind Zone 2 listing at https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
