Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Reka, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Bryan.
Key Points
- ◦Benton serves Nevils, Southward, Lanier and Letford and other communities around Reka.
- ◦In Reka, a building permit is required once the garage exceeds 200 square feet.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF..
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
29
As of 2026 · Source |
Permits & Setbacks in Bryan County
Before a metal garage goes up in Reka, check with Bryan County Community Development Department, Building and Codes Division — Bryan's cutoff for requiring a building permit is 200 square feet. Below that, you still need to clear the Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF. setback from your property line.
Delivery to Reka
Current delivery time to Reka is approximately 1 to 2 weeks. Benton also serves nearby communities including Nevils, Southward, Lanier and Letford. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Bryan County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Reka before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Reka?
Current delivery time to Reka is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Bryan County Community Development Department, Building and Codes Division. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Reka, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How far is Benton Metal Depot from Reka?
Benton Metal Depot's Statesboro location is approximately 19.2 miles from Reka. The company serves residents throughout Bryan, including communities such as Nevils, Southward, Lanier and Letford. Current delivery time for a metal garage to the Reka area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Reka is Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF., although you should confirm the requirement for your particular property with Bryan County Community Development Department, Building and Codes Division. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Bryan County Community Development Department, Building and Codes Division has requirements that can affect garage placement, including a current setback of Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
Reka, Bryan County — At a Glance
- Permit Authority Name
- Bryan County Community Development Department, Building and Codes Division
- Permit Authority Url
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
- Wind Load Zone
- Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 19.2
- Drive Minutes
- 29
- Nearby Towns
- Nevils, Southward, Lanier, Letford
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Reka, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Reka?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes (2026)
- https://www.bryancountyga.gov/government/departments-a-g/community-development/building-and-codes/learn-more ("buildings greater than 200 square feet in size" require a building permit) (2026)
- Bryan County Code of Ordinances Ch. 114, Sec. 114-611, as summarized at https://www.zoneomics.com/code/bryan-county-unincorporated-GA/chapter_6 — verify against primary ordinance at https://library.municode.com/ga/bryan_county (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (primary: lists Bryan among the 6 GA Wind Zone 2 coastal counties: Chatham, Bryan, Liberty, McIntosh, Glynn, Camden) — mph range aggregated from windload.solutions/homenation.com secondary sources (2026)
- Given/client spec — Bryan County is a coastal Georgia county; confirmed independently by its Wind Zone 2 listing at https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
