Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Letford? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Bryan, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦The current local setback for a metal garage is Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦In Letford, a building permit is required once the garage exceeds 200 square feet.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
29
As of 2026 · Source |
Permits & Setbacks in Bryan County
Before a metal garage goes up in Letford, check with Bryan County Community Development Department, Building and Codes Division — Bryan's cutoff for requiring a building permit is 200 square feet. Below that, you still need to clear the Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF. setback from your property line.
Delivery to Letford
Current delivery time to Letford is approximately 1 to 2 weeks. Benton also serves nearby communities including Nevils, Southward, Lanier and Groveland. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Bryan County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Bryan County Community Development Department, Building and Codes Division. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Letford before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Letford?
Current delivery time to Letford is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How far is Benton Metal Depot from Letford?
Benton Metal Depot's Statesboro location is approximately 19.2 miles from Letford. The company serves residents throughout Bryan, including communities such as Nevils, Southward, Lanier and Groveland. Current delivery time for a metal garage to the Letford area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Letford is Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF., although you should confirm the requirement for your particular property with Bryan County Community Development Department, Building and Codes Division. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Letford, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Definitions
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
Letford, Bryan County — At a Glance
- Permit Authority Name
- Bryan County Community Development Department, Building and Codes Division
- Permit Authority Url
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not fully published in a single accessible table — the Unified Development/Zoning Ordinance (Ch. 114, Art. V/VI) sets district-specific setbacks. District-by-district side/rear figures for accessory buildings need to be pulled from the primary ordinance PDF.
- Wind Load Zone
- Coastal Georgia — Georgia Dept. of Insurance/Safety Fire places Bryan County in Wind Zone 2 (110-130 mph HUD manufactured-housing standard). Secondary sources put ASCE 7 ultimate design wind speeds for this part of coastal GA in the general 130-140 mph range. Exact figure depends on ASCE 7 edition/exposure/risk category and must be confirmed with a GA-licensed engineer or the county building official before publishing.
- Coastal
- 1
- Drive Miles
- 19.2
- Drive Minutes
- 29
- Nearby Towns
- Nevils, Southward, Lanier, Groveland
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Letford and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Letford?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.bryancountyga.gov/government/departments-a-g/building-and-codes (2026)
- https://www.bryancountyga.gov/government/departments-a-g/community-development/building-and-codes/learn-more ("buildings greater than 200 square feet in size" require a building permit) (2026)
- Bryan County Code of Ordinances Ch. 114, Sec. 114-611, as summarized at https://www.zoneomics.com/code/bryan-county-unincorporated-GA/chapter_6 — verify against primary ordinance at https://library.municode.com/ga/bryan_county (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (primary: lists Bryan among the 6 GA Wind Zone 2 coastal counties: Chatham, Bryan, Liberty, McIntosh, Glynn, Camden) — mph range aggregated from windload.solutions/homenation.com secondary sources (2026)
- Given/client spec — Bryan County is a coastal Georgia county; confirmed independently by its Wind Zone 2 listing at https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
