Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Broadfield? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Glynn, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts..
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton serves Sterling, Pennick, Boys Estate and Altamaha Park and other communities around Broadfield.
- ◦In Broadfield, a building permit is required once the garage exceeds Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet.
At a Glance
| Permit threshold |
Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia (Brunswick/St. Simons Island) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II), with barrier-island parcels potentially higher. NOT verified against a primary Glynn County map; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
122
As of 2026 · Source |
Permits & Setbacks in Glynn County
The permit question for a Broadfield metal garage comes down to one number from Glynn County Building, Permitting and Inspections: Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet. Stay under it and skip the full permit process; either way, keep the Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts. setback in mind before you pick a spot.
Delivery to Broadfield
The current estimate for getting a metal garage to Broadfield is 1 to 2 weeks. The area is about 104.7 miles (122 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Glynn County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Glynn County Building, Permitting and Inspections. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Broadfield?
That depends on the garage and the requirements of Glynn County Building, Permitting and Inspections. The current rule requires a permit once the garage exceeds Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Broadfield, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How long does it take to get a metal garage delivered to Broadfield?
Current delivery time to Broadfield is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Broadfield before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Glynn County Building, Permitting and Inspections has requirements that can affect garage placement, including a current setback of Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Definitions
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
Broadfield, Glynn County — At a Glance
- Permit Authority Name
- Glynn County Building, Permitting and Inspections
- Permit Authority Url
- https://www.glynncounty.org/876/Building-Code-Enforcements
- Permit Threshold Sqft
- Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections.
- Setback Feet Side Rear
- Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.
- Wind Load Zone
- Coastal Georgia (Brunswick/St. Simons Island) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II), with barrier-island parcels potentially higher. NOT verified against a primary Glynn County map; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- 1
- Drive Miles
- 104.7
- Drive Minutes
- 122
- Nearby Towns
- Sterling, Pennick, Boys Estate, Altamaha Park
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Broadfield, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Broadfield?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.glynncounty.org/876/Building-Code-Enforcements (2026)
- Glynn County Zoning and Subdivision Ordinance, Sec. 610, https://library.municode.com/ga/glynn_county/codes/zoning_and_subdivision_ordinance — needs direct lookup (2026)
- Aggregated from windload.solutions and similar secondary sources — no primary Glynn County wind map found (2026)
- Given/client spec — Glynn County (Brunswick/St. Simons) is a coastal Georgia county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Glynn County
See the Glynn County hub for metal garages
