Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Country Club Estates and across Glynn, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 104.7 miles from Country Club Estates.
- ◦Delivery to Country Club Estates is currently estimated at 1 to 2 weeks.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦In Country Club Estates, a building permit is required once the garage exceeds Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet.
At a Glance
| Permit threshold |
Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia (Brunswick/St. Simons Island) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II), with barrier-island parcels potentially higher. NOT verified against a primary Glynn County map; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
122
As of 2026 · Source |
Permits & Setbacks in Glynn County
Before a metal garage goes up in Country Club Estates, check with Glynn County Building, Permitting and Inspections — Glynn's cutoff for requiring a building permit is Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet. Below that, you still need to clear the Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts. setback from your property line.
Delivery to Country Club Estates
The current estimate for getting a metal garage to Country Club Estates is 1 to 2 weeks. The area is about 104.7 miles (122 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Glynn County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Country Club Estates before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Country Club Estates?
Current delivery time to Country Club Estates is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
How far is Benton Metal Depot from Country Club Estates?
Benton Metal Depot's Statesboro location is approximately 104.7 miles from Country Club Estates. The company serves residents throughout Glynn, including communities such as Sterling, Pennick, Boys Estate and Broadfield. Current delivery time for a metal garage to the Country Club Estates area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Country Club Estates is Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts., although you should confirm the requirement for your particular property with Glynn County Building, Permitting and Inspections. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Glynn County Building, Permitting and Inspections has requirements that can affect garage placement, including a current setback of Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Definitions
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
Country Club Estates, Glynn County — At a Glance
- Permit Authority Name
- Glynn County Building, Permitting and Inspections
- Permit Authority Url
- https://www.glynncounty.org/876/Building-Code-Enforcements
- Permit Threshold Sqft
- Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections.
- Setback Feet Side Rear
- Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.
- Wind Load Zone
- Coastal Georgia (Brunswick/St. Simons Island) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II), with barrier-island parcels potentially higher. NOT verified against a primary Glynn County map; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- 1
- Drive Miles
- 104.7
- Drive Minutes
- 122
- Nearby Towns
- Sterling, Pennick, Boys Estate, Broadfield
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Country Club Estates and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Country Club Estates?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.glynncounty.org/876/Building-Code-Enforcements (2026)
- Glynn County Zoning and Subdivision Ordinance, Sec. 610, https://library.municode.com/ga/glynn_county/codes/zoning_and_subdivision_ordinance — needs direct lookup (2026)
- Aggregated from windload.solutions and similar secondary sources — no primary Glynn County wind map found (2026)
- Given/client spec — Glynn County (Brunswick/St. Simons) is a coastal Georgia county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Glynn County
See the Glynn County hub for metal garages
