Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Sterling and across Glynn, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 104.7 miles from Sterling.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Delivery to Sterling is currently estimated at 1 to 2 weeks.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia (Brunswick/St. Simons Island) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II), with barrier-island parcels potentially higher. NOT verified against a primary Glynn County map; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
122
As of 2026 · Source |
Permits & Setbacks in Glynn County
Glynn's permitting office, Glynn County Building, Permitting and Inspections, sets the accessory-structure line at Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet — build under that and you generally skip the full building-permit process, though a setback of Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Sterling
The current estimate for getting a metal garage to Sterling is 1 to 2 weeks. The area is about 104.7 miles (122 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Glynn County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Sterling, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How far is Benton Metal Depot from Sterling?
Benton Metal Depot's Statesboro location is approximately 104.7 miles from Sterling. The company serves residents throughout Glynn, including communities such as Pennick, Boys Estate, Broadfield and Altamaha Park. Current delivery time for a metal garage to the Sterling area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Sterling is Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts., although you should confirm the requirement for your particular property with Glynn County Building, Permitting and Inspections. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Sterling before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Glynn County Building, Permitting and Inspections. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How long does it take to get a metal garage delivered to Sterling?
Current delivery time to Sterling is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Do I need a permit for a metal garage in Sterling?
That depends on the garage and the requirements of Glynn County Building, Permitting and Inspections. The current rule requires a permit once the garage exceeds Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Definitions
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
Sterling, Glynn County — At a Glance
- Permit Authority Name
- Glynn County Building, Permitting and Inspections
- Permit Authority Url
- https://www.glynncounty.org/876/Building-Code-Enforcements
- Permit Threshold Sqft
- Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections.
- Setback Feet Side Rear
- Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.
- Wind Load Zone
- Coastal Georgia (Brunswick/St. Simons Island) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II), with barrier-island parcels potentially higher. NOT verified against a primary Glynn County map; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- 1
- Drive Miles
- 104.7
- Drive Minutes
- 122
- Nearby Towns
- Pennick, Boys Estate, Broadfield, Altamaha Park
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Sterling, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Sterling?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.glynncounty.org/876/Building-Code-Enforcements (2026)
- Glynn County Zoning and Subdivision Ordinance, Sec. 610, https://library.municode.com/ga/glynn_county/codes/zoning_and_subdivision_ordinance — needs direct lookup (2026)
- Aggregated from windload.solutions and similar secondary sources — no primary Glynn County wind map found (2026)
- Given/client spec — Glynn County (Brunswick/St. Simons) is a coastal Georgia county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Glynn County
See the Glynn County hub for metal garages
