Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Brobston and across Glynn, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦In Brobston, a building permit is required once the garage exceeds Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet.
- ◦Benton serves Sterling, Pennick, Boys Estate and Broadfield and other communities around Brobston.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦The current local setback for a metal garage is Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.
As of 2026 · Source |
| Wind load zone |
Coastal Georgia (Brunswick/St. Simons Island) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II), with barrier-island parcels potentially higher. NOT verified against a primary Glynn County map; must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
122
As of 2026 · Source |
Permits & Setbacks in Glynn County
Glynn treats a metal garage like any other accessory structure: under Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet, Glynn County Building, Permitting and Inspections typically doesn't require a full permit, but the Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts. setback rule still governs where it can sit on the lot.
Delivery to Brobston
The current estimate for getting a metal garage to Brobston is 1 to 2 weeks. The area is about 104.7 miles (122 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Glynn County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Brobston, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Do I need a permit for a metal garage in Brobston?
That depends on the garage and the requirements of Glynn County Building, Permitting and Inspections. The current rule requires a permit once the garage exceeds Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Glynn County Building, Permitting and Inspections. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
How far is Benton Metal Depot from Brobston?
Benton Metal Depot's Statesboro location is approximately 104.7 miles from Brobston. The company serves residents throughout Glynn, including communities such as Sterling, Pennick, Boys Estate and Broadfield. Current delivery time for a metal garage to the Brobston area is about 1 to 2 weeks.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How close can my metal garage be to the property line?
The current setback in Brobston is Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts., although you should confirm the requirement for your particular property with Glynn County Building, Permitting and Inspections. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
Brobston, Glynn County — At a Glance
- Permit Authority Name
- Glynn County Building, Permitting and Inspections
- Permit Authority Url
- https://www.glynncounty.org/876/Building-Code-Enforcements
- Permit Threshold Sqft
- Not found — the county publishes a fee estimate for a 200 sq ft carport permit (~$30) implying that size requires a permit, but no explicit exemption threshold below which no permit is needed was located. Needs direct confirmation with Glynn County Building, Permitting and Inspections.
- Setback Feet Side Rear
- Not retrieved — Glynn County Zoning and Subdivision Ordinance Section 610 ("Setback and Other Yard Requirements for Accessory Uses") governs this, but specific footage figures were not retrievable from search excerpts.
- Wind Load Zone
- Coastal Georgia (Brunswick/St. Simons Island) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II), with barrier-island parcels potentially higher. NOT verified against a primary Glynn County map; must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- 1
- Drive Miles
- 104.7
- Drive Minutes
- 122
- Nearby Towns
- Sterling, Pennick, Boys Estate, Broadfield
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Brobston and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Brobston?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.glynncounty.org/876/Building-Code-Enforcements (2026)
- Glynn County Zoning and Subdivision Ordinance, Sec. 610, https://library.municode.com/ga/glynn_county/codes/zoning_and_subdivision_ordinance — needs direct lookup (2026)
- Aggregated from windload.solutions and similar secondary sources — no primary Glynn County wind map found (2026)
- Given/client spec — Glynn County (Brunswick/St. Simons) is a coastal Georgia county (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Glynn County
See the Glynn County hub for metal garages
