Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Bartow, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Jefferson and the surrounding area.
Key Points
- ◦Delivery to Bartow is currently estimated at 1 to 2 weeks.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 65.8 miles from Bartow.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification.
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
92
As of 2026 · Source |
Permits & Setbacks in Jefferson County
Jefferson treats a metal garage like any other accessory structure: under No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet, Jefferson County Building Permits & Inspections / Code Enforcement Department typically doesn't require a full permit, but the Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text. setback rule still governs where it can sit on the lot.
Delivery to Bartow
Current delivery time to Bartow is approximately 1 to 2 weeks. Benton also serves nearby communities including Almira, Pine Hill, Moxley and Wadley. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Jefferson County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How close can my metal garage be to the property line?
The current setback in Bartow is Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text., although you should confirm the requirement for your particular property with Jefferson County Building Permits & Inspections / Code Enforcement Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Bartow?
Benton Metal Depot's Statesboro location is approximately 65.8 miles from Bartow. The company serves residents throughout Jefferson, including communities such as Almira, Pine Hill, Moxley and Wadley. Current delivery time for a metal garage to the Bartow area is about 1 to 2 weeks.
How long does it take to get a metal garage delivered to Bartow?
Current delivery time to Bartow is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Bartow before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Jefferson County Building Permits & Inspections / Code Enforcement Department has requirements that can affect garage placement, including a current setback of Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Definitions
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
Bartow, Jefferson County — At a Glance
- Permit Authority Name
- Jefferson County Building Permits & Inspections / Code Enforcement Department
- Permit Authority Url
- https://www.jeffersoncountyga.gov/184/Building-Permit-Procedure
- Permit Threshold Sqft
- No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification.
- Setback Feet Side Rear
- Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.
- Wind Load Zone
- Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 65.8
- Drive Minutes
- 92
- Nearby Towns
- Almira, Pine Hill, Moxley, Wadley
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Bartow and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Bartow?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.jeffersoncountyga.gov/183/Building-Permits-Inspections (2026)
- https://www.jeffersoncountyga.gov/184/Building-Permit-Procedure (2026)
- https://www.jeffersoncountyga.gov/184/Building-Permit-Procedure and https://library.municode.com/ga/jefferson_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH20LAUSDE_ARTXIVZODI (2026)
- Jefferson County Code of Ordinances, Ch. 20, Art. XIV at https://library.municode.com/ga/jefferson_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH20LAUSDE_ARTXIVZODI (2026)
- https://oci.georgia.gov/inspections-permits-plans/manufactured-housing/wind-zones (confirms Jefferson County is not one of the 6 GA Wind Zone 2 coastal counties) — general ASCE 7 range aggregated from windload.solutions (2026)
- Jefferson County (Louisville, GA) is inland central-east Georgia and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
