Metal Garages in Stapletons Crossroads 2026

Georgia Jefferson County Stapletons Crossroads

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

If you're shopping for a metal garage in Stapletons Crossroads, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Jefferson.

Key Points

◦Doors, windows and other selections can change the final cost of a garage.
◦The current local setback for a metal garage is Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text..
◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
◦In Stapletons Crossroads, a building permit is required once the garage exceeds No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet.
◦Benton serves Rosier, Old Town, Louisville and Pine Hill and other communities around Stapletons Crossroads.

At a Glance

Permit threshold	No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. As of 2026 · Source
Setback (side/rear)	Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text. As of 2026 · Source
Wind load zone	Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	97 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Jefferson County

Jefferson treats a metal garage like any other accessory structure: under No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet, Jefferson County Building Permits & Inspections / Code Enforcement Department typically doesn't require a full permit, but the Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text. setback rule still governs where it can sit on the lot.

Delivery to Stapletons Crossroads

Current delivery time to Stapletons Crossroads is approximately 1 to 2 weeks. Benton also serves nearby communities including Rosier, Old Town, Louisville and Pine Hill. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.

Representative product photo — a Jefferson County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Stapletons Crossroads, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

Do I need a permit for a metal garage in Stapletons Crossroads?

That depends on the garage and the requirements of Jefferson County Building Permits & Inspections / Code Enforcement Department. The current rule requires a permit once the garage exceeds No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with Jefferson County Building Permits & Inspections / Code Enforcement Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

Should I pour the concrete before ordering the garage?

Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Stapletons Crossroads before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.

Definitions

◦ Wall Panel: Formed metal sheet used to enclose and protect the exterior walls of the garage.
◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.
◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.

Stapletons Crossroads, Jefferson County — At a Glance

Permit Authority Name: Jefferson County Building Permits & Inspections / Code Enforcement Department
Permit Authority Url: https://www.jeffersoncountyga.gov/184/Building-Permit-Procedure
Permit Threshold Sqft: No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification.
Setback Feet Side Rear: Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.
Wind Load Zone: Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
Coastal
Drive Miles: 66.3
Drive Minutes: 97
Nearby Towns: Rosier, Old Town, Louisville, Pine Hill
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Stapletons Crossroads and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.

Ready to talk through your metal garages project in Stapletons Crossroads?

Call (912) 489-5795

Sources

Other Cities We Serve in Jefferson County

See the Jefferson County hub for metal garages

Almira Atwell Avera Bartow Ellis Plantation Louisville Matthews Moxley Noah Old Town Omaha Springs Pine Hill Stapleton Stapletons Crossroads Stellaville Wadley Wrens Zebina

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Stapletons Crossroads, Jefferson County, Georgia (2026)