Metal Garages in Moxley 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Moxley and across Jefferson, with different building sizes depending on the amount of space the property owner needs.

Key Points

◦Benton serves Pine Hill, Wadley, Almira and Bartow and other communities around Moxley.
◦In Moxley, a building permit is required once the garage exceeds No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet.
◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
◦The current local setback for a metal garage is Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text..
◦Check the permit and setback rules before deciding exactly where the garage will go.

At a Glance

Permit threshold	No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. As of 2026 · Source
Setback (side/rear)	Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text. As of 2026 · Source
Wind load zone	Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	84 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Jefferson County

Jefferson's permitting office, Jefferson County Building Permits & Inspections / Code Enforcement Department, sets the accessory-structure line at No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet — build under that and you generally skip the full building-permit process, though a setback of Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.

Delivery to Moxley

Metal garage delivery to Moxley can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.

Representative product photo — a Jefferson County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

Do I need a permit for a metal garage in Moxley?

That depends on the garage and the requirements of Jefferson County Building Permits & Inspections / Code Enforcement Department. The current rule requires a permit once the garage exceeds No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Moxley, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with Jefferson County Building Permits & Inspections / Code Enforcement Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

How close can my metal garage be to the property line?

The current setback in Moxley is Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text., although you should confirm the requirement for your particular property with Jefferson County Building Permits & Inspections / Code Enforcement Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

Definitions

◦ Roof Pitch: How steep the roof is, usually described by how much it rises over a set horizontal distance.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.
◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.

Moxley, Jefferson County — At a Glance

Permit Authority Name: Jefferson County Building Permits & Inspections / Code Enforcement Department
Permit Authority Url: https://www.jeffersoncountyga.gov/184/Building-Permit-Procedure
Permit Threshold Sqft: No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification.
Setback Feet Side Rear: Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.
Wind Load Zone: Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
Coastal
Drive Miles: 60.1
Drive Minutes: 84
Nearby Towns: Pine Hill, Wadley, Almira, Bartow
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Moxley, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.

Ready to talk through your metal garages project in Moxley?

Call (912) 489-5795

Sources

Other Cities We Serve in Jefferson County

See the Jefferson County hub for metal garages

Almira Atwell Avera Bartow Ellis Plantation Louisville Matthews Moxley Noah Old Town Omaha Springs Pine Hill Stapleton Stapletons Crossroads Stellaville Wadley Wrens Zebina

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Moxley, Jefferson County, Georgia (2026)