Metal Garages in Wrens 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

If you're shopping for a metal garage in Wrens, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Jefferson.

Key Points

◦Benton Metal Depot is approximately 76.4 miles from Wrens.
◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
◦Doors, windows and other selections can change the final cost of a garage.
◦Get the final garage dimensions before completing permanent site work.
◦Delivery to Wrens is currently estimated at 1 to 2 weeks.

At a Glance

Permit threshold	No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. As of 2026 · Source
Setback (side/rear)	Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text. As of 2026 · Source
Wind load zone	Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	100 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Jefferson County

Jefferson treats a metal garage like any other accessory structure: under No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet, Jefferson County Building Permits & Inspections / Code Enforcement Department typically doesn't require a full permit, but the Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text. setback rule still governs where it can sit on the lot.

Delivery to Wrens

Metal garage delivery to Wrens can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.

Representative product photo — a Jefferson County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

Do I need a permit for a metal garage in Wrens?

That depends on the garage and the requirements of Jefferson County Building Permits & Inspections / Code Enforcement Department. The current rule requires a permit once the garage exceeds No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification. square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

How much extra room should I allow around my vehicles?

Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

Can I put a metal garage beside my house?

You may be able to, but don't assume every open spot on the property is buildable. Jefferson County Building Permits & Inspections / Code Enforcement Department has requirements that can affect garage placement, including a current setback of Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.

How far is Benton Metal Depot from Wrens?

Benton Metal Depot's Statesboro location is approximately 76.4 miles from Wrens. The company serves residents throughout Jefferson, including communities such as Stellaville, Zebina, Ellis Plantation and Atwell. Current delivery time for a metal garage to the Wrens area is about 1 to 2 weeks.

Definitions

◦ Setback: The required amount of space between your garage and a property line, road or another boundary covered by local rules.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.
◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Wall Panel: Formed metal sheet used to enclose and protect the exterior walls of the garage.
◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.
◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
◦ Building Permit: Approval from the local government to construct a building under the building and zoning rules that apply to the property.
◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.

Wrens, Jefferson County — At a Glance

Permit Authority Name: Jefferson County Building Permits & Inspections / Code Enforcement Department
Permit Authority Url: https://www.jeffersoncountyga.gov/184/Building-Permit-Procedure
Permit Threshold Sqft: No explicit accessory-structure permit-exemption sqft was found. The zoning ordinance separately caps "mini-structures" (storage sheds) at no more than 200 sq ft per lot in most residential districts, but this reads as a maximum storage allowance rather than a no-permit-needed threshold — needs direct clarification.
Setback Feet Side Rear: Not independently pulled from the primary ordinance in a district-by-district table. The zoning resolution states accessory buildings must meet "the setback requirements for a dwelling or accessory building (whichever is less) in the applicable district" — actual side/rear foot figures per district need to be pulled from the primary Municode text.
Wind Load Zone: Inland Georgia — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; needs confirmation with a GA-licensed engineer or the county building official.
Coastal
Drive Miles: 76.4
Drive Minutes: 100
Nearby Towns: Stellaville, Zebina, Ellis Plantation, Atwell
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Wrens, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.

Ready to talk through your metal garages project in Wrens?

Call (912) 489-5795

Sources

Other Cities We Serve in Jefferson County

See the Jefferson County hub for metal garages

Almira Atwell Avera Bartow Ellis Plantation Louisville Matthews Moxley Noah Old Town Omaha Springs Pine Hill Stapleton Stapletons Crossroads Stellaville Wadley Wrens Zebina

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Wrens, Jefferson County, Georgia (2026)