Metal Garages in Bellville Point 2026

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

For some residents in Bellville Point, a metal garage means covered parking. For others, it's where the lawn equipment, tools and weekend projects end up. Benton Metal Depot supplies metal garage packages throughout McIntosh, so the building can be planned around the job it needs to do on your property.

Key Points

◦Benton Metal Depot is approximately 81.6 miles from Bellville Point.
◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
◦Get the final garage dimensions before completing permanent site work.
◦Delivery to Bellville Point is currently estimated at 1 to 2 weeks.
◦Doors, windows and other selections can change the final cost of a garage.

At a Glance

Permit threshold	Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). As of 2026 · Source
Setback (side/rear)	Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance. As of 2026 · Source
Wind load zone	Coastal Georgia (Darien) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II) for this stretch of coastal GA, consistent with Chatham/Glynn. NOT verified against a primary McIntosh County map; must be confirmed with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	97 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in McIntosh County

The permit question for a Bellville Point metal garage comes down to one number from McIntosh County Building & Zoning Office: Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). square feet. Stay under it and skip the full permit process; either way, keep the Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance. setback in mind before you pick a spot.

Delivery to Bellville Point

Metal garage delivery to Bellville Point can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.

Representative product photo — a McIntosh County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

Do I need a permit for a metal garage in Bellville Point?

That depends on the garage and the requirements of McIntosh County Building & Zoning Office. The current rule requires a permit once the garage exceeds Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Bellville Point, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with McIntosh County Building & Zoning Office. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

How close can my metal garage be to the property line?

The current setback in Bellville Point is Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance., although you should confirm the requirement for your particular property with McIntosh County Building & Zoning Office. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

Definitions

◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Roof Pitch: How steep the roof is, usually described by how much it rises over a set horizontal distance.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.
◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.
◦ Setback: The required amount of space between your garage and a property line, road or another boundary covered by local rules.
◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.

Bellville Point, McIntosh County — At a Glance

Permit Authority Name: McIntosh County Building & Zoning Office
Permit Authority Url: https://www.mcintoshcountyga.com/253/Building-Zoning
Permit Threshold Sqft: Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603).
Setback Feet Side Rear: Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance.
Wind Load Zone: Coastal Georgia (Darien) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II) for this stretch of coastal GA, consistent with Chatham/Glynn. NOT verified against a primary McIntosh County map; must be confirmed with a GA-licensed engineer or the county building official.
Coastal: 1
Drive Miles: 81.6
Drive Minutes: 97
Nearby Towns: Eulonia, Crescent, Townsend, Cox
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Bellville Point, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.

Ready to talk through your metal garages project in Bellville Point?

Call (912) 489-5795

Sources

Other Cities We Serve in McIntosh County

See the McIntosh County hub for metal garages

Ardick Ashintilly Bellville Point Brickston Carnigan Cedar Point Cox Credit Hill Crescent Darien Eulonia Fairhope Huxford Jones Julienton Meridian Pine Harbor Raccoon Bluff Ridgeville Sapelo Island Shellman Bluff South Newport Townsend Valona

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Bellville Point, McIntosh County, Georgia (2026)