Metal Garages in Fairhope 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

Do you need more room for vehicles, tools or equipment in Fairhope? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout McIntosh, with buildings that you can plan around according to what you need to park, store or work on.

Key Points

◦In Fairhope, a building permit is required once the garage exceeds Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). square feet.
◦Benton serves Eulonia, Crescent, Bellville Point and Townsend and other communities around Fairhope.
◦Check the permit and setback rules before deciding exactly where the garage will go.
◦The current local setback for a metal garage is Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance..
◦Plan for door clearance and walking room when deciding how wide your garage needs to be.

At a Glance

Permit threshold	Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). As of 2026 · Source
Setback (side/rear)	Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance. As of 2026 · Source
Wind load zone	Coastal Georgia (Darien) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II) for this stretch of coastal GA, consistent with Chatham/Glynn. NOT verified against a primary McIntosh County map; must be confirmed with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	97 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in McIntosh County

McIntosh's permitting office, McIntosh County Building & Zoning Office, sets the accessory-structure line at Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). square feet — build under that and you generally skip the full building-permit process, though a setback of Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.

Delivery to Fairhope

Metal garage delivery to Fairhope can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.

Representative product photo — a McIntosh County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

How much extra room should I allow around my vehicles?

Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.

Can I put a metal garage beside my house?

You may be able to, but don't assume every open spot on the property is buildable. McIntosh County Building & Zoning Office has requirements that can affect garage placement, including a current setback of Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.

Should I pour the concrete before ordering the garage?

Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Fairhope before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.

How long does it take to get a metal garage delivered to Fairhope?

Current delivery time to Fairhope is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.

How far is Benton Metal Depot from Fairhope?

Benton Metal Depot's Statesboro location is approximately 81.6 miles from Fairhope. The company serves residents throughout McIntosh, including communities such as Eulonia, Crescent, Bellville Point and Townsend. Current delivery time for a metal garage to the Fairhope area is about 1 to 2 weeks.

How close can my metal garage be to the property line?

The current setback in Fairhope is Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance., although you should confirm the requirement for your particular property with McIntosh County Building & Zoning Office. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

Definitions

◦ Setback: The required amount of space between your garage and a property line, road or another boundary covered by local rules.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.
◦ Wall Panel: Formed metal sheet used to enclose and protect the exterior walls of the garage.
◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.
◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
◦ Building Permit: Approval from the local government to construct a building under the building and zoning rules that apply to the property.
◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.

Fairhope, McIntosh County — At a Glance

Permit Authority Name: McIntosh County Building & Zoning Office
Permit Authority Url: https://www.mcintoshcountyga.com/253/Building-Zoning
Permit Threshold Sqft: Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603).
Setback Feet Side Rear: Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance.
Wind Load Zone: Coastal Georgia (Darien) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II) for this stretch of coastal GA, consistent with Chatham/Glynn. NOT verified against a primary McIntosh County map; must be confirmed with a GA-licensed engineer or the county building official.
Coastal: 1
Drive Miles: 81.6
Drive Minutes: 97
Nearby Towns: Eulonia, Crescent, Bellville Point, Townsend
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Fairhope, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.

Ready to talk through your metal garages project in Fairhope?

Call (912) 489-5795

Sources

Other Cities We Serve in McIntosh County

See the McIntosh County hub for metal garages

Ardick Ashintilly Bellville Point Brickston Carnigan Cedar Point Cox Credit Hill Crescent Darien Eulonia Fairhope Huxford Jones Julienton Meridian Pine Harbor Raccoon Bluff Ridgeville Sapelo Island Shellman Bluff South Newport Townsend Valona

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Fairhope, McIntosh County, Georgia (2026)