Metal Garages in Carnigan 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Carnigan and across McIntosh, with different building sizes depending on the amount of space the property owner needs.

Key Points

◦Doors, windows and other selections can change the final cost of a garage.
◦In Carnigan, a building permit is required once the garage exceeds Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). square feet.
◦Benton serves Meridian, Ridgeville, Ardick and Ashintilly and other communities around Carnigan.
◦The current local setback for a metal garage is Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance..
◦Plan for door clearance and walking room when deciding how wide your garage needs to be.

At a Glance

Permit threshold	Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). As of 2026 · Source
Setback (side/rear)	Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance. As of 2026 · Source
Wind load zone	Coastal Georgia (Darien) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II) for this stretch of coastal GA, consistent with Chatham/Glynn. NOT verified against a primary McIntosh County map; must be confirmed with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	110 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in McIntosh County

McIntosh treats a metal garage like any other accessory structure: under Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). square feet, McIntosh County Building & Zoning Office typically doesn't require a full permit, but the Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance. setback rule still governs where it can sit on the lot.

Delivery to Carnigan

Current delivery time to Carnigan is approximately 1 to 2 weeks. Benton also serves nearby communities including Meridian, Ridgeville, Ardick and Ashintilly. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.

Representative product photo — a McIntosh County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

How close can my metal garage be to the property line?

The current setback in Carnigan is Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance., although you should confirm the requirement for your particular property with McIntosh County Building & Zoning Office. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

How far is Benton Metal Depot from Carnigan?

Benton Metal Depot's Statesboro location is approximately 95.4 miles from Carnigan. The company serves residents throughout McIntosh, including communities such as Meridian, Ridgeville, Ardick and Ashintilly. Current delivery time for a metal garage to the Carnigan area is about 1 to 2 weeks.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Carnigan, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

How long does it take to get a metal garage delivered to Carnigan?

Current delivery time to Carnigan is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with McIntosh County Building & Zoning Office. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

Should I pour the concrete before ordering the garage?

Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Carnigan before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

Definitions

◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Roof Pitch: How steep the roof is, usually described by how much it rises over a set horizontal distance.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.

Carnigan, McIntosh County — At a Glance

Permit Authority Name: McIntosh County Building & Zoning Office
Permit Authority Url: https://www.mcintoshcountyga.com/253/Building-Zoning
Permit Threshold Sqft: Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603).
Setback Feet Side Rear: Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance.
Wind Load Zone: Coastal Georgia (Darien) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II) for this stretch of coastal GA, consistent with Chatham/Glynn. NOT verified against a primary McIntosh County map; must be confirmed with a GA-licensed engineer or the county building official.
Coastal: 1
Drive Miles: 95.4
Drive Minutes: 110
Nearby Towns: Meridian, Ridgeville, Ardick, Ashintilly
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Carnigan and throughout the region to help them choose a garage package that will work well with whatever they need.

Ready to talk through your metal garages project in Carnigan?

Call (912) 489-5795

Sources

Other Cities We Serve in McIntosh County

See the McIntosh County hub for metal garages

Ardick Ashintilly Bellville Point Brickston Carnigan Cedar Point Cox Credit Hill Crescent Darien Eulonia Fairhope Huxford Jones Julienton Meridian Pine Harbor Raccoon Bluff Ridgeville Sapelo Island Shellman Bluff South Newport Townsend Valona

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Carnigan, McIntosh County, Georgia (2026)