Metal Garages in Meridian 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

Do you need more room for vehicles, tools or equipment in Meridian? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout McIntosh, with buildings that you can plan around according to what you need to park, store or work on.

Key Points

◦Doors, windows and other selections can change the final cost of a garage.
◦Benton Metal Depot is approximately 95.4 miles from Meridian.
◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
◦Delivery to Meridian is currently estimated at 1 to 2 weeks.
◦Get the final garage dimensions before completing permanent site work.

At a Glance

Permit threshold	Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). As of 2026 · Source
Setback (side/rear)	Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance. As of 2026 · Source
Wind load zone	Coastal Georgia (Darien) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II) for this stretch of coastal GA, consistent with Chatham/Glynn. NOT verified against a primary McIntosh County map; must be confirmed with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	110 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in McIntosh County

The permit question for a Meridian metal garage comes down to one number from McIntosh County Building & Zoning Office: Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603). square feet. Stay under it and skip the full permit process; either way, keep the Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance. setback in mind before you pick a spot.

Delivery to Meridian

Residents in Meridian are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 95.4 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.

Representative product photo — a McIntosh County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with McIntosh County Building & Zoning Office. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

How close can my metal garage be to the property line?

The current setback in Meridian is Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance., although you should confirm the requirement for your particular property with McIntosh County Building & Zoning Office. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

How far is Benton Metal Depot from Meridian?

Benton Metal Depot's Statesboro location is approximately 95.4 miles from Meridian. The company serves residents throughout McIntosh, including communities such as Ridgeville, Ardick, Carnigan and Ashintilly. Current delivery time for a metal garage to the Meridian area is about 1 to 2 weeks.

How long does it take to get a metal garage delivered to Meridian?

Current delivery time to Meridian is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.

Should I pour the concrete before ordering the garage?

Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Meridian before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Meridian, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

Can I put a metal garage beside my house?

You may be able to, but don't assume every open spot on the property is buildable. McIntosh County Building & Zoning Office has requirements that can affect garage placement, including a current setback of Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.

How much extra room should I allow around my vehicles?

Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.

Definitions

◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.
◦ Wall Panel: Formed metal sheet used to enclose and protect the exterior walls of the garage.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.
◦ Setback: The required amount of space between your garage and a property line, road or another boundary covered by local rules.
◦ Building Permit: Approval from the local government to construct a building under the building and zoning rules that apply to the property.
◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.

Meridian, McIntosh County — At a Glance

Permit Authority Name: McIntosh County Building & Zoning Office
Permit Authority Url: https://www.mcintoshcountyga.com/253/Building-Zoning
Permit Threshold Sqft: Not found — the county publishes an Accessory Building Permit application but no sqft exemption threshold was confirmed in available materials. Needs direct confirmation (912-437-6603).
Setback Feet Side Rear: Not confirmed for accessory structures specifically. For reference, the R-1 Single-Family Residential district principal-structure minimums are 10 ft side yard / 15 ft rear yard from the property line, and max lot coverage including accessory buildings is 40% in R-1 / 30% in A-R (Residential Agriculture); accessory-structure-specific setback figures need direct lookup in the 2025 zoning ordinance.
Wind Load Zone: Coastal Georgia (Darien) — secondary sources commonly cite around 130 mph (ASCE 7-22, Risk Category II) for this stretch of coastal GA, consistent with Chatham/Glynn. NOT verified against a primary McIntosh County map; must be confirmed with a GA-licensed engineer or the county building official.
Coastal: 1
Drive Miles: 95.4
Drive Minutes: 110
Nearby Towns: Ridgeville, Ardick, Carnigan, Ashintilly
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Meridian and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.

Ready to talk through your metal garages project in Meridian?

Call (912) 489-5795

Sources

Other Cities We Serve in McIntosh County

See the McIntosh County hub for metal garages

Ardick Ashintilly Bellville Point Brickston Carnigan Cedar Point Cox Credit Hill Crescent Darien Eulonia Fairhope Huxford Jones Julienton Meridian Pine Harbor Raccoon Bluff Ridgeville Sapelo Island Shellman Bluff South Newport Townsend Valona

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Meridian, McIntosh County, Georgia (2026)