Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Cobbtown, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Tattnall.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Benton Metal Depot is approximately 32.1 miles from Cobbtown.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Delivery to Cobbtown is currently estimated at 1 to 2 weeks.
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Tattnall County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
45
As of 2026 · Source |
Permits & Setbacks in Tattnall County
Before a metal garage goes up in Cobbtown, check with Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office) — Tattnall's cutoff for requiring a building permit is Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335). square feet. Below that, you still need to clear the Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation. setback from your property line.
Delivery to Cobbtown
Current delivery time to Cobbtown is approximately 1 to 2 weeks. Benton also serves nearby communities including Manassas, Collins, Aline and Olifftown. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Tattnall County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office) has requirements that can affect garage placement, including a current setback of Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Do I need a permit for a metal garage in Cobbtown?
That depends on the garage and the requirements of Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office). The current rule requires a permit once the garage exceeds Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
Cobbtown, Tattnall County — At a Glance
- Permit Authority Name
- Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office)
- Permit Authority Url
- https://www.tattnallcountyga.com/planning-and-zoning.cfm
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335).
- Setback Feet Side Rear
- Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Tattnall County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 32.1
- Drive Minutes
- 45
- Nearby Towns
- Manassas, Collins, Aline, Olifftown
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Cobbtown, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Cobbtown?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.tattnallcountyga.com/planning-and-zoning.cfm (2026)
- No primary source found; https://www.tattnallcountyga.com/planning-and-zoning.cfm does not publish a threshold (2026)
- https://library.municode.com/ga/tattnall_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH42MOHOMAHO (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Tattnall County is inland (southeast GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
