Reviewed by the Benton Metal Depot team · Updated
If you're shopping for a metal garage in Glennville, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Tattnall.
Key Points
- ◦The current local setback for a metal garage is Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦In Glennville, a building permit is required once the garage exceeds Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335). square feet.
- ◦Benton serves Beards Creek, Lynn, Tison and Mendes and other communities around Glennville.
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Tattnall County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
58
As of 2026 · Source |
Permits & Setbacks in Tattnall County
The permit question for a Glennville metal garage comes down to one number from Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office): Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335). square feet. Stay under it and skip the full permit process; either way, keep the Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation. setback in mind before you pick a spot.
Delivery to Glennville
Current delivery time to Glennville is approximately 1 to 2 weeks. Benton also serves nearby communities including Beards Creek, Lynn, Tison and Mendes. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Tattnall County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How far is Benton Metal Depot from Glennville?
Benton Metal Depot's Statesboro location is approximately 38.1 miles from Glennville. The company serves residents throughout Tattnall, including communities such as Beards Creek, Lynn, Tison and Mendes. Current delivery time for a metal garage to the Glennville area is about 1 to 2 weeks.
How close can my metal garage be to the property line?
The current setback in Glennville is Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation., although you should confirm the requirement for your particular property with Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Glennville before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office) has requirements that can affect garage placement, including a current setback of Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How long does it take to get a metal garage delivered to Glennville?
Current delivery time to Glennville is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Definitions
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
Glennville, Tattnall County — At a Glance
- Permit Authority Name
- Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office)
- Permit Authority Url
- https://www.tattnallcountyga.com/planning-and-zoning.cfm
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335).
- Setback Feet Side Rear
- Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Tattnall County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 38.1
- Drive Minutes
- 58
- Nearby Towns
- Beards Creek, Lynn, Tison, Mendes
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Glennville, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Glennville?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.tattnallcountyga.com/planning-and-zoning.cfm (2026)
- No primary source found; https://www.tattnallcountyga.com/planning-and-zoning.cfm does not publish a threshold (2026)
- https://library.municode.com/ga/tattnall_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH42MOHOMAHO (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Tattnall County is inland (southeast GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
