Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Collins and across Tattnall, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Delivery to Collins is currently estimated at 1 to 2 weeks.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 31.4 miles from Collins.
- ◦The current local setback for a metal garage is Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation..
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Tattnall County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
52
As of 2026 · Source |
Permits & Setbacks in Tattnall County
Tattnall treats a metal garage like any other accessory structure: under Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335). square feet, Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office) typically doesn't require a full permit, but the Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation. setback rule still governs where it can sit on the lot.
Delivery to Collins
Residents in Collins are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 31.4 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Tattnall County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Do I need a permit for a metal garage in Collins?
That depends on the garage and the requirements of Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office). The current rule requires a permit once the garage exceeds Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office) has requirements that can affect garage placement, including a current setback of Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Collins before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Definitions
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
Collins, Tattnall County — At a Glance
- Permit Authority Name
- Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office)
- Permit Authority Url
- https://www.tattnallcountyga.com/planning-and-zoning.cfm
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335).
- Setback Feet Side Rear
- Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Tattnall County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 31.4
- Drive Minutes
- 52
- Nearby Towns
- Manassas, Cobbtown, Daniels, Hughland
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Collins and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Collins?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.tattnallcountyga.com/planning-and-zoning.cfm (2026)
- No primary source found; https://www.tattnallcountyga.com/planning-and-zoning.cfm does not publish a threshold (2026)
- https://library.municode.com/ga/tattnall_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH42MOHOMAHO (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Tattnall County is inland (southeast GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
