Reviewed by the Benton Metal Depot team · Updated
One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Tison, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Tattnall and the surrounding area.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Benton Metal Depot is approximately 38.1 miles from Tison.
- ◦Delivery to Tison is currently estimated at 1 to 2 weeks.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.
As of 2026 · Source |
| Wind load zone |
Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Tattnall County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
58
As of 2026 · Source |
Permits & Setbacks in Tattnall County
Before a metal garage goes up in Tison, check with Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office) — Tattnall's cutoff for requiring a building permit is Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335). square feet. Below that, you still need to clear the Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation. setback from your property line.
Delivery to Tison
Current delivery time to Tison is approximately 1 to 2 weeks. Benton also serves nearby communities including Beards Creek, Lynn, Mendes and Glennville. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Tattnall County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
How long does it take to get a metal garage delivered to Tison?
Current delivery time to Tison is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Tison before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office). Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Tison, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How close can my metal garage be to the property line?
The current setback in Tison is Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation., although you should confirm the requirement for your particular property with Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office). A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Tison?
Benton Metal Depot's Statesboro location is approximately 38.1 miles from Tison. The company serves residents throughout Tattnall, including communities such as Beards Creek, Lynn, Mendes and Glennville. Current delivery time for a metal garage to the Tison area is about 1 to 2 weeks.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office) has requirements that can affect garage placement, including a current setback of Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Definitions
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
Tison, Tattnall County — At a Glance
- Permit Authority Name
- Tattnall County Planning and Zoning Department (permits also filed/issued through the County Clerk's Office)
- Permit Authority Url
- https://www.tattnallcountyga.com/planning-and-zoning.cfm
- Permit Threshold Sqft
- Not found — no published sqft exemption for accessory structures located on the county site. Needs direct confirmation with Tattnall County Planning and Zoning (912-557-4335).
- Setback Feet Side Rear
- Not found — the Tattnall County Code of Ordinances (Municode Chapter 42) addresses mobile homes, but a general accessory-structure setback table was not located via search. Needs direct confirmation.
- Wind Load Zone
- Inland Georgia — roughly 110-120 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7 edition Tattnall County has adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 38.1
- Drive Minutes
- 58
- Nearby Towns
- Beards Creek, Lynn, Mendes, Glennville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Tison, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Tison?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.tattnallcountyga.com/planning-and-zoning.cfm (2026)
- No primary source found; https://www.tattnallcountyga.com/planning-and-zoning.cfm does not publish a threshold (2026)
- https://library.municode.com/ga/tattnall_county/codes/code_of_ordinances?nodeId=PTIICOOR_CH42MOHOMAHO (2026)
- General ASCE 7 inland-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Tattnall County is inland (southeast GA) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
