Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Bolen can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Ware and can help you find the building depending on how the space will actually be used.
Key Points
- ◦The current local setback for a metal garage is Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦In Bolen, a building permit is required once the garage exceeds Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet.
At a Glance
| Permit threshold |
Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
148
As of 2026 · Source |
Permits & Setbacks in Ware County
Ware treats a metal garage like any other accessory structure: under Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet, Ware County Planning & Codes Department typically doesn't require a full permit, but the Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes. setback rule still governs where it can sit on the lot.
Delivery to Bolen
Residents in Bolen are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 98.9 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Ware County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Do I need a permit for a metal garage in Bolen?
That depends on the garage and the requirements of Ware County Planning & Codes Department. The current rule requires a permit once the garage exceeds Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Ware County Planning & Codes Department has requirements that can affect garage placement, including a current setback of Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
How close can my metal garage be to the property line?
The current setback in Bolen is Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes., although you should confirm the requirement for your particular property with Ware County Planning & Codes Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
Definitions
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
Bolen, Ware County — At a Glance
- Permit Authority Name
- Ware County Planning & Codes Department
- Permit Authority Url
- https://www.warecountyga.gov/department-nodes/planning-codes
- Permit Threshold Sqft
- Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379).
- Setback Feet Side Rear
- Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.
- Wind Load Zone
- Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 98.9
- Drive Minutes
- 148
- Nearby Towns
- Waresboro, Dixie Union, Skullhead, Sappville
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Bolen and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Bolen?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.warecountyga.gov/department-nodes/planning-codes (2026)
- https://cdn.prod.website-files.com/63d5ca60103cc0d24935804f/6a04892b6f4197158d50f3ea_2026-05-WARE-COUNTY-ZONING-ORDINANCE-ARTICLES-3-THRU-12.pdf (2026)
- General ASCE 7 southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Ware County is inland (Waycross area) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
