Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Millwood can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Ware and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦The current local setback for a metal garage is Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes..
- ◦Benton serves Hasty, Fairfax, Axson and Manor and other communities around Millwood.
- ◦In Millwood, a building permit is required once the garage exceeds Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet.
At a Glance
| Permit threshold |
Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
172
As of 2026 · Source |
Permits & Setbacks in Ware County
The permit question for a Millwood metal garage comes down to one number from Ware County Planning & Codes Department: Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet. Stay under it and skip the full permit process; either way, keep the Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes. setback in mind before you pick a spot.
Delivery to Millwood
The current estimate for getting a metal garage to Millwood is 1 to 2 weeks. The area is about 131.8 miles (172 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.
Representative product photo — a Ware County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Ware County Planning & Codes Department has requirements that can affect garage placement, including a current setback of Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Millwood?
That depends on the garage and the requirements of Ware County Planning & Codes Department. The current rule requires a permit once the garage exceeds Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Millwood before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Definitions
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
Millwood, Ware County — At a Glance
- Permit Authority Name
- Ware County Planning & Codes Department
- Permit Authority Url
- https://www.warecountyga.gov/department-nodes/planning-codes
- Permit Threshold Sqft
- Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379).
- Setback Feet Side Rear
- Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.
- Wind Load Zone
- Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 131.8
- Drive Minutes
- 172
- Nearby Towns
- Hasty, Fairfax, Axson, Manor
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Millwood and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Millwood?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.warecountyga.gov/department-nodes/planning-codes (2026)
- https://cdn.prod.website-files.com/63d5ca60103cc0d24935804f/6a04892b6f4197158d50f3ea_2026-05-WARE-COUNTY-ZONING-ORDINANCE-ARTICLES-3-THRU-12.pdf (2026)
- General ASCE 7 southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Ware County is inland (Waycross area) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
