Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Hebardville? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Ware, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Benton Metal Depot is approximately 99.4 miles from Hebardville.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Delivery to Hebardville is currently estimated at 1 to 2 weeks.
- ◦Doors, windows and other selections can change the final cost of a garage.
At a Glance
| Permit threshold |
Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.
As of 2026 · Source |
| Wind load zone |
Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
149
As of 2026 · Source |
Permits & Setbacks in Ware County
Before a metal garage goes up in Hebardville, check with Ware County Planning & Codes Department — Ware's cutoff for requiring a building permit is Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet. Below that, you still need to clear the Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes. setback from your property line.
Delivery to Hebardville
Metal garage delivery to Hebardville can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Ware County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Hebardville, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
How long does it take to get a metal garage delivered to Hebardville?
Current delivery time to Hebardville is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Hebardville before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How close can my metal garage be to the property line?
The current setback in Hebardville is Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes., although you should confirm the requirement for your particular property with Ware County Planning & Codes Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Ware County Planning & Codes Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How far is Benton Metal Depot from Hebardville?
Benton Metal Depot's Statesboro location is approximately 99.4 miles from Hebardville. The company serves residents throughout Ware, including communities such as Sunnyside, Deenwood, Waycross and Bolen. Current delivery time for a metal garage to the Hebardville area is about 1 to 2 weeks.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
Hebardville, Ware County — At a Glance
- Permit Authority Name
- Ware County Planning & Codes Department
- Permit Authority Url
- https://www.warecountyga.gov/department-nodes/planning-codes
- Permit Threshold Sqft
- Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379).
- Setback Feet Side Rear
- Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.
- Wind Load Zone
- Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 99.4
- Drive Minutes
- 149
- Nearby Towns
- Sunnyside, Deenwood, Waycross, Bolen
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Hebardville and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Hebardville?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.warecountyga.gov/department-nodes/planning-codes (2026)
- https://cdn.prod.website-files.com/63d5ca60103cc0d24935804f/6a04892b6f4197158d50f3ea_2026-05-WARE-COUNTY-ZONING-ORDINANCE-ARTICLES-3-THRU-12.pdf (2026)
- General ASCE 7 southeast-Georgia range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Ware County is inland (Waycross area) and is not among the coastal counties named in the client spec (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
