Metal Garages in Winona Park 2026

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Winona Park, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Ware and the surrounding area.

Key Points

◦Doors, windows and other selections can change the final cost of a garage.
◦In Winona Park, a building permit is required once the garage exceeds Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet.
◦Benton serves Bolen, Waresboro, Dixie Union and Skullhead and other communities around Winona Park.
◦The current local setback for a metal garage is Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes..
◦Plan for door clearance and walking room when deciding how wide your garage needs to be.

At a Glance

Permit threshold	Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). As of 2026 · Source
Setback (side/rear)	Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes. As of 2026 · Source
Wind load zone	Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	148 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Ware County

The permit question for a Winona Park metal garage comes down to one number from Ware County Planning & Codes Department: Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet. Stay under it and skip the full permit process; either way, keep the Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes. setback in mind before you pick a spot.

Delivery to Winona Park

Metal garage delivery to Winona Park can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.

Representative product photo — a Ware County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Do I need a permit for a metal garage in Winona Park?

That depends on the garage and the requirements of Ware County Planning & Codes Department. The current rule requires a permit once the garage exceeds Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with Ware County Planning & Codes Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Winona Park, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

Can I put a metal garage beside my house?

You may be able to, but don't assume every open spot on the property is buildable. Ware County Planning & Codes Department has requirements that can affect garage placement, including a current setback of Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.

How much extra room should I allow around my vehicles?

Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.

How close can my metal garage be to the property line?

The current setback in Winona Park is Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes., although you should confirm the requirement for your particular property with Ware County Planning & Codes Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

Definitions

◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Wall Panel: Formed metal sheet used to enclose and protect the exterior walls of the garage.
◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.
◦ Setback: The required amount of space between your garage and a property line, road or another boundary covered by local rules.
◦ Roof Pitch: How steep the roof is, usually described by how much it rises over a set horizontal distance.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.

Winona Park, Ware County — At a Glance

Permit Authority Name: Ware County Planning & Codes Department
Permit Authority Url: https://www.warecountyga.gov/department-nodes/planning-codes
Permit Threshold Sqft: Not explicitly published on the county's Planning & Codes page. A 200 sq ft threshold is common across several nearby GA counties (confirmed directly for Wayne and Burke) — but that has NOT been confirmed as unincorporated Ware County's own adopted rule. Confirm directly with Ware County Planning & Codes (912-490-4379).
Setback Feet Side Rear: Not found with specific numbers. The county's zoning ordinance exists as a PDF but its accessory-structure setback table could not be extracted as text in this pass. Needs a manual review of the primary PDF or direct confirmation with Planning & Codes.
Wind Load Zone: Southeast Georgia coastal plain (Waycross area, ~55-65 miles from the Atlantic) — roughly 115-130 mph (ASCE 7, Exposure C). NOT a verified figure; exact design wind speed depends on the ASCE 7/IBC edition adopted and must be confirmed with a GA-licensed engineer or the county building official.
Coastal
Drive Miles: 98.9
Drive Minutes: 148
Nearby Towns: Bolen, Waresboro, Dixie Union, Skullhead
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Winona Park and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.

Ready to talk through your metal garages project in Winona Park?

Call (912) 489-5795

Sources

Other Cities We Serve in Ware County

See the Ware County hub for metal garages

Astoria Beach Bickley Bolen Braganza Crawley Deenwood Dixie Union Emerson Park Fairfax Glenmore Hasty Haywood Hebardville Hopkins Jamestown Manor Millwood Needham Ruskin Sappville Skullhead Sunnyside Three Points Wahoma Waltertown Waresboro Waycross Winona Park

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Winona Park, Ware County, Georgia (2026)