Metal Garages in Hagoods Mill 2026

South Carolina Barnwell County Hagoods Mill

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

A garage doesn't have to be just a place to park the car. Property owners in Hagoods Mill can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Barnwell and can help you find the building depending on how the space will actually be used.

Key Points

◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
◦The current local setback for a metal garage is Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category..
◦Check the permit and setback rules before deciding exactly where the garage will go.
◦Benton serves Patterson Mill, Yenome, Owens Crossroad and Kline and other communities around Hagoods Mill.
◦In Hagoods Mill, a building permit is required once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet.

At a Glance

Permit threshold	Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). As of 2026 · Source
Setback (side/rear)	Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category. As of 2026 · Source
Wind load zone	Inland South Carolina — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	96 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Barnwell County

Before a metal garage goes up in Hagoods Mill, check with Barnwell County Building Inspector & Zoning — Barnwell's cutoff for requiring a building permit is Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet. Below that, you still need to clear the Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category. setback from your property line.

Delivery to Hagoods Mill

Metal garage delivery to Hagoods Mill can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.

Representative product photo — a Barnwell County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with Barnwell County Building Inspector & Zoning. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

Do I need a permit for a metal garage in Hagoods Mill?

That depends on the garage and the requirements of Barnwell County Building Inspector & Zoning. The current rule requires a permit once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Hagoods Mill, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

How close can my metal garage be to the property line?

The current setback in Hagoods Mill is Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category., although you should confirm the requirement for your particular property with Barnwell County Building Inspector & Zoning. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

Can I put a metal garage beside my house?

You may be able to, but don't assume every open spot on the property is buildable. Barnwell County Building Inspector & Zoning has requirements that can affect garage placement, including a current setback of Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.

How much extra room should I allow around my vehicles?

Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.

Definitions

◦ Building Permit: Approval from the local government to construct a building under the building and zoning rules that apply to the property.
◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.
◦ Wall Panel: Formed metal sheet used to enclose and protect the exterior walls of the garage.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.
◦ Setback: The required amount of space between your garage and a property line, road or another boundary covered by local rules.
◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.

Hagoods Mill, Barnwell County — At a Glance

Permit Authority Name: Barnwell County Building Inspector & Zoning
Permit Authority Url: https://www.barnwellcountysc.us/163/Building-Inspector-Zoning
Permit Threshold Sqft: Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593).
Setback Feet Side Rear: Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category.
Wind Load Zone: Inland South Carolina — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
Coastal
Drive Miles: 72.1
Drive Minutes: 96
Nearby Towns: Patterson Mill, Yenome, Owens Crossroad, Kline
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Hagoods Mill and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.

Ready to talk through your metal garages project in Hagoods Mill?

Call (912) 489-5795

Sources

Other Cities We Serve in Barnwell County

See the Barnwell County hub for metal garages

Ashleigh Barnwell Blackville Elko Farrells Mill Hagoods Mill Hattieville Healing Springs Hilda Kline Owens Crossroad Patterson Mill Reynold Snelling Walker Whaley Williston Yenome

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Hagoods Mill, Barnwell County, South Carolina (2026)