Metal Garages in Hilda 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

A garage doesn't have to be just a place to park the car. Property owners in Hilda can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Barnwell and can help you find the building depending on how the space will actually be used.

Key Points

◦Get the final garage dimensions before completing permanent site work.
◦In Hilda, a building permit is required once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet.
◦Benton serves Patterson Mill, Yenome, Hagoods Mill and Owens Crossroad and other communities around Hilda.
◦The current local setback for a metal garage is Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category..
◦Plan for door clearance and walking room when deciding how wide your garage needs to be.

At a Glance

Permit threshold	Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). As of 2026 · Source
Setback (side/rear)	Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category. As of 2026 · Source
Wind load zone	Inland South Carolina — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	96 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Barnwell County

Before a metal garage goes up in Hilda, check with Barnwell County Building Inspector & Zoning — Barnwell's cutoff for requiring a building permit is Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet. Below that, you still need to clear the Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category. setback from your property line.

Delivery to Hilda

Current delivery time to Hilda is approximately 1 to 2 weeks. Benton also serves nearby communities including Patterson Mill, Yenome, Hagoods Mill and Owens Crossroad. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.

Representative product photo — a Barnwell County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

How long does it take to get a metal garage delivered to Hilda?

Current delivery time to Hilda is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Hilda, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

Should I pour the concrete before ordering the garage?

Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Hilda before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with Barnwell County Building Inspector & Zoning. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

How close can my metal garage be to the property line?

The current setback in Hilda is Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category., although you should confirm the requirement for your particular property with Barnwell County Building Inspector & Zoning. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

How far is Benton Metal Depot from Hilda?

Benton Metal Depot's Statesboro location is approximately 72.1 miles from Hilda. The company serves residents throughout Barnwell, including communities such as Patterson Mill, Yenome, Hagoods Mill and Owens Crossroad. Current delivery time for a metal garage to the Hilda area is about 1 to 2 weeks.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

Definitions

◦ Wall Panel: Formed metal sheet used to enclose and protect the exterior walls of the garage.
◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.
◦ Walk Door: A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
◦ Eave Height: The height of the sidewall measured to the point where the wall and roof meet.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
◦ Concrete Slab: A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Building Permit: Approval from the local government to construct a building under the building and zoning rules that apply to the property.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.

Hilda, Barnwell County — At a Glance

Permit Authority Name: Barnwell County Building Inspector & Zoning
Permit Authority Url: https://www.barnwellcountysc.us/163/Building-Inspector-Zoning
Permit Threshold Sqft: Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593).
Setback Feet Side Rear: Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category.
Wind Load Zone: Inland South Carolina — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
Coastal
Drive Miles: 72.1
Drive Minutes: 96
Nearby Towns: Patterson Mill, Yenome, Hagoods Mill, Owens Crossroad
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Hilda and throughout the region to help them choose a garage package that will work well with whatever they need.

Ready to talk through your metal garages project in Hilda?

Call (912) 489-5795

Sources

Other Cities We Serve in Barnwell County

See the Barnwell County hub for metal garages

Ashleigh Barnwell Blackville Elko Farrells Mill Hagoods Mill Hattieville Healing Springs Hilda Kline Owens Crossroad Patterson Mill Reynold Snelling Walker Whaley Williston Yenome

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Hilda, Barnwell County, South Carolina (2026)