Metal Garages in Patterson Mill 2026

South Carolina Barnwell County Patterson Mill

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

One mistake people make when planning a garage is sizing it for what they own today. If you're building your garage in Patterson Mill, think about storage, door clearance, work space and what might be added later. Benton Metal Depot supplies metal garage packages for residents throughout Barnwell and the surrounding area.

Key Points

◦Benton serves Yenome, Hagoods Mill, Owens Crossroad and Kline and other communities around Patterson Mill.
◦In Patterson Mill, a building permit is required once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet.
◦Check the permit and setback rules before deciding exactly where the garage will go.
◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
◦The current local setback for a metal garage is Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category..

At a Glance

Permit threshold	Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). As of 2026 · Source
Setback (side/rear)	Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category. As of 2026 · Source
Wind load zone	Inland South Carolina — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	96 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Barnwell County

Barnwell treats a metal garage like any other accessory structure: under Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet, Barnwell County Building Inspector & Zoning typically doesn't require a full permit, but the Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category. setback rule still governs where it can sit on the lot.

Delivery to Patterson Mill

The current estimate for getting a metal garage to Patterson Mill is 1 to 2 weeks. The area is about 72.1 miles (96 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.

Representative product photo — a Barnwell County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

Can I put a metal garage beside my house?

You may be able to, but don't assume every open spot on the property is buildable. Barnwell County Building Inspector & Zoning has requirements that can affect garage placement, including a current setback of Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.

How much extra room should I allow around my vehicles?

Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.

How far is Benton Metal Depot from Patterson Mill?

Benton Metal Depot's Statesboro location is approximately 72.1 miles from Patterson Mill. The company serves residents throughout Barnwell, including communities such as Yenome, Hagoods Mill, Owens Crossroad and Kline. Current delivery time for a metal garage to the Patterson Mill area is about 1 to 2 weeks.

How close can my metal garage be to the property line?

The current setback in Patterson Mill is Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category., although you should confirm the requirement for your particular property with Barnwell County Building Inspector & Zoning. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.

Should I pour the concrete before ordering the garage?

Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Patterson Mill before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.

How long does it take to get a metal garage delivered to Patterson Mill?

Current delivery time to Patterson Mill is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.

Can my metal garage have windows and different doors?

The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.

What can I keep in a metal garage?

Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.

Definitions

◦ Building Permit: Approval from the local government to construct a building under the building and zoning rules that apply to the property.
◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.
◦ Roof Pitch: How steep the roof is, usually described by how much it rises over a set horizontal distance.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.
◦ Setback: The required amount of space between your garage and a property line, road or another boundary covered by local rules.
◦ Trim: The finished metal pieces used along corners, roof edges, openings and other transitions on the building.

Patterson Mill, Barnwell County — At a Glance

Permit Authority Name: Barnwell County Building Inspector & Zoning
Permit Authority Url: https://www.barnwellcountysc.us/163/Building-Inspector-Zoning
Permit Threshold Sqft: Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593).
Setback Feet Side Rear: Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category.
Wind Load Zone: Inland South Carolina — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
Coastal
Drive Miles: 72.1
Drive Minutes: 96
Nearby Towns: Yenome, Hagoods Mill, Owens Crossroad, Kline
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Patterson Mill, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.

Ready to talk through your metal garages project in Patterson Mill?

Call (912) 489-5795

Sources

Other Cities We Serve in Barnwell County

See the Barnwell County hub for metal garages

Ashleigh Barnwell Blackville Elko Farrells Mill Hagoods Mill Hattieville Healing Springs Hilda Kline Owens Crossroad Patterson Mill Reynold Snelling Walker Whaley Williston Yenome

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Patterson Mill, Barnwell County, South Carolina (2026)