Metal Garages in Yenome 2026 | Benton Metal Depot

Reviewed by the Benton Metal Depot team · Updated October 1, 2026

If you're shopping for a metal garage in Yenome, don't start with the building size. Instead, you should start with what you're planning to put inside it. A pickup, two cars and a workbench all need different amounts of room. Benton Metal Depot supplies garage packages for residential, agricultural and commercial properties throughout Barnwell.

Key Points

◦In Yenome, a building permit is required once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet.
◦Benton serves Patterson Mill, Hagoods Mill, Owens Crossroad and Kline and other communities around Yenome.
◦Check the permit and setback rules before deciding exactly where the garage will go.
◦The current local setback for a metal garage is Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category..
◦Plan for door clearance and walking room when deciding how wide your garage needs to be.

At a Glance

Permit threshold	Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). As of 2026 · Source
Setback (side/rear)	Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category. As of 2026 · Source
Wind load zone	Inland South Carolina — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official. As of 2026 · Source
Panel type/gauge	29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures. As of 2026 · Source
Drive time from Statesboro	96 As of 2026 · Source

Call (912) 489-5795 Design in 3D

Permits & Setbacks in Barnwell County

Before a metal garage goes up in Yenome, check with Barnwell County Building Inspector & Zoning — Barnwell's cutoff for requiring a building permit is Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet. Below that, you still need to clear the Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category. setback from your property line.

Delivery to Yenome

The current estimate for getting a metal garage to Yenome is 1 to 2 weeks. The area is about 72.1 miles (96 minutes) from Benton Metal Depot in Statesboro. That gives you a general timeline for scheduling contractors, preparing the property and handling local permits before the building is due to arrive.

Representative product photo — a Barnwell County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).

FAQ

What do I need to do to my property before the garage arrives?

First, decide exactly where the garage will go and check the permit and setback requirements with Barnwell County Building Inspector & Zoning. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.

Can I use a metal garage just for storage?

Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.

Do I need a permit for a metal garage in Yenome?

That depends on the garage and the requirements of Barnwell County Building Inspector & Zoning. The current rule requires a permit once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.

Can I use my metal garage as a workshop too?

Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.

Are metal garages a good choice for Georgia?

Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Yenome, make sure the garage specifications and site plan also meet the local requirements that apply to the property.

How much extra room should I allow around my vehicles?

Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.

Can I put a metal garage beside my house?

You may be able to, but don't assume every open spot on the property is buildable. Barnwell County Building Inspector & Zoning has requirements that can affect garage placement, including a current setback of Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.

How far is Benton Metal Depot from Yenome?

Benton Metal Depot's Statesboro location is approximately 72.1 miles from Yenome. The company serves residents throughout Barnwell, including communities such as Patterson Mill, Hagoods Mill, Owens Crossroad and Kline. Current delivery time for a metal garage to the Yenome area is about 1 to 2 weeks.

Definitions

◦ Building Permit: Approval from the local government to construct a building under the building and zoning rules that apply to the property.
◦ Ridge: The top line of a pitched roof where the two sloping sides come together.
◦ Overhead Door: The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
◦ Building Footprint: The amount of ground the garage takes up, based on its outside width and length.
◦ Roof Panel: A formed sheet of metal that makes up part of the garage's exterior roof surface.
◦ Fastener: A screw or other connector used to hold metal panels and building components securely in place.
◦ Gable: The triangular wall section found at the end of a building with a pitched roof.
◦ Setback: The required amount of space between your garage and a property line, road or another boundary covered by local rules.
◦ Roof Pitch: How steep the roof is, usually described by how much it rises over a set horizontal distance.
◦ Clear Span: Open floor space between the building's exterior supports without interior columns getting in the way.

Yenome, Barnwell County — At a Glance

Permit Authority Name: Barnwell County Building Inspector & Zoning
Permit Authority Url: https://www.barnwellcountysc.us/163/Building-Inspector-Zoning
Permit Threshold Sqft: Not found — no explicit sqft exemption for accessory structures located on the county site. Carports appear to require a permit regardless of size per county guidance. Needs direct confirmation (839-279-9593).
Setback Feet Side Rear: Not retrieved — Barnwell County's Land Development Regulations (PDF) likely contain a district setback table but the specific side/rear figures for accessory structures were not retrievable from search excerpts. Note: Barnwell County zoning code reportedly does not clearly address ADUs/accessory structures as a distinct use category.
Wind Load Zone: Inland South Carolina — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
Coastal
Drive Miles: 72.1
Drive Minutes: 96
Nearby Towns: Patterson Mill, Hagoods Mill, Owens Crossroad, Kline
Delivery Weeks In Stock: 1
Delivery Weeks Custom: 2
Panel Type Gauge: 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
Color Count: 7

Why Benton Metal Depot

Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Yenome and throughout the region to help them choose a garage package that will work well with whatever they need.

Ready to talk through your metal garages project in Yenome?

Call (912) 489-5795

Sources

Other Cities We Serve in Barnwell County

See the Barnwell County hub for metal garages

Ashleigh Barnwell Blackville Elko Farrells Mill Hagoods Mill Hattieville Healing Springs Hilda Kline Owens Crossroad Patterson Mill Reynold Snelling Walker Whaley Williston Yenome

Call Design

High-quality metal roofing installation example by Benton Metal Depot

Get Started

Let our team work with you and in turn, earn you more business. We strive to provide our service the right way, offering quality products at competitive prices. You can be assured that we will give you an unmatched customer service just as you expect.

Premium metal roofing panels engineered for weather resistance
Architectural metal siding for modern aesthetic appeal
Residential & commercial project solutions
Satisfaction materials with exceptional longevity

Get Your Free Metal Building Quote

Tell us a bit about your project and we'll get back to you with a custom quote — no obligation, no pressure.

Full Name *

Phone Number *

Email Address *

Project Details *

Get a Quick Quote

Metal Garage for your Metal Garages in Yenome, Barnwell County, South Carolina (2026)