Reviewed by the Benton Metal Depot team · Updated
A garage doesn't have to be just a place to park the car. Property owners in Badham can use metal garages to store cleaning equipment, different kinds of tools, storage and it can be used as a work space, too. Benton Metal Depot serves customers across Dorchester and can help you find the building depending on how the space will actually be used.
Key Points
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦In Badham, a building permit is required once the garage exceeds 200 square feet.
- ◦Benton serves Dorange, Reevesville, Grover and Byrd and other communities around Badham.
- ◦The current local setback for a metal garage is Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011..
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
As of 2026 · Source |
| Wind load zone |
Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
146
As of 2026 · Source |
Permits & Setbacks in Dorchester County
Dorchester treats a metal garage like any other accessory structure: under 200 square feet, Dorchester County Building Services Department typically doesn't require a full permit, but the Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011. setback rule still governs where it can sit on the lot.
Delivery to Badham
Current delivery time to Badham is approximately 1 to 2 weeks. Benton also serves nearby communities including Dorange, Reevesville, Grover and Byrd. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Dorchester County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Badham, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Badham?
That depends on the garage and the requirements of Dorchester County Building Services Department. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Dorchester County Building Services Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
How close can my metal garage be to the property line?
The current setback in Badham is Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011., although you should confirm the requirement for your particular property with Dorchester County Building Services Department. A setback controls how close the building can be to certain property boundaries. Check that distance before you settle on a location, especially when space on the lot is tight.
How far is Benton Metal Depot from Badham?
Benton Metal Depot's Statesboro location is approximately 108.9 miles from Badham. The company serves residents throughout Dorchester, including communities such as Dorange, Reevesville, Grover and Byrd. Current delivery time for a metal garage to the Badham area is about 1 to 2 weeks.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
Definitions
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
Badham, Dorchester County — At a Glance
- Permit Authority Name
- Dorchester County Building Services Department
- Permit Authority Url
- https://www.dorchestercountysc.gov/government/building-services/submittal-process
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
- Wind Load Zone
- Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 108.9
- Drive Minutes
- 146
- Nearby Towns
- Dorange, Reevesville, Grover, Byrd
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot manufactures metal products in Statesboro and has served residential, agricultural and commercial customers since 2004. For someone building a garage in Badham, that means working with a regional metal supplier rather than trying to piece the project together from unrelated sources. The garage package can be quoted around the specifications of the project.
Ready to talk through your metal garages project in Badham?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.dorchestercountysc.gov/government/building-services (2026)
- https://www.dorchestercountysc.gov/government/building-services/submittal-process (2026)
- South Carolina Residential Code § R105.2 (2018 IRC as adopted statewide, incl. Dorchester County): one-story detached accessory structures used as tool/storage sheds, playhouses, etc. are exempt from a building permit if floor area ≤200 sq ft AND the structure has no electrical/plumbing/mechanical connections. Not independently re-confirmed on Dorchester's own permitting page (403'd on fetch) — verify against Dorchester's current submittal guide before publishing. (2026)
- https://www.dorchestercountysc.gov/government/planning-development/planning-zoning/zoning-and-land-development-standards (2026)
- General ASCE 7 coastal-plain-SC range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Dorchester County is not among the coastal counties named in the client spec, though it borders Charleston and Berkeley counties (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
