Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Pregnall? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Dorchester, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Benton Metal Depot is approximately 123.3 miles from Pregnall.
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦Delivery to Pregnall is currently estimated at 1 to 2 weeks.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
As of 2026 · Source |
| Wind load zone |
Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
167
As of 2026 · Source |
Permits & Setbacks in Dorchester County
Dorchester treats a metal garage like any other accessory structure: under 200 square feet, Dorchester County Building Services Department typically doesn't require a full permit, but the Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011. setback rule still governs where it can sit on the lot.
Delivery to Pregnall
Metal garage delivery to Pregnall can take about 1 to 2 weeks. Use that time to take care of permits and get the site ready if work is needed beforehand. If you're hiring someone for grading or concrete, coordinate those jobs around the delivery schedule instead of trying to squeeze everything in at the last minute.
Representative product photo — a Dorchester County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Pregnall, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Pregnall?
That depends on the garage and the requirements of Dorchester County Building Services Department. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Dorchester County Building Services Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Pregnall before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Definitions
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
Pregnall, Dorchester County — At a Glance
- Permit Authority Name
- Dorchester County Building Services Department
- Permit Authority Url
- https://www.dorchestercountysc.gov/government/building-services/submittal-process
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
- Wind Load Zone
- Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 123.3
- Drive Minutes
- 167
- Nearby Towns
- Dorchester, Givhans, Pringletown, Canaan
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Pregnall and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Pregnall?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.dorchestercountysc.gov/government/building-services (2026)
- https://www.dorchestercountysc.gov/government/building-services/submittal-process (2026)
- South Carolina Residential Code § R105.2 (2018 IRC as adopted statewide, incl. Dorchester County): one-story detached accessory structures used as tool/storage sheds, playhouses, etc. are exempt from a building permit if floor area ≤200 sq ft AND the structure has no electrical/plumbing/mechanical connections. Not independently re-confirmed on Dorchester's own permitting page (403'd on fetch) — verify against Dorchester's current submittal guide before publishing. (2026)
- https://www.dorchestercountysc.gov/government/planning-development/planning-zoning/zoning-and-land-development-standards (2026)
- General ASCE 7 coastal-plain-SC range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Dorchester County is not among the coastal counties named in the client spec, though it borders Charleston and Berkeley counties (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
