Reviewed by the Benton Metal Depot team · Updated
Do you need more room for vehicles, tools or equipment in Reevesville? A metal garage might be the solution! It gives you enclosed space without adding onto your house or existing building. Benton Metal Depot supplies metal garage packages throughout Dorchester, with buildings that you can plan around according to what you need to park, store or work on.
Key Points
- ◦Delivery to Reevesville is currently estimated at 1 to 2 weeks.
- ◦Benton Metal Depot is approximately 108.9 miles from Reevesville.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Get the final garage dimensions before completing permanent site work.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
As of 2026 · Source |
| Wind load zone |
Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
146
As of 2026 · Source |
Permits & Setbacks in Dorchester County
Dorchester's permitting office, Dorchester County Building Services Department, sets the accessory-structure line at 200 square feet — build under that and you generally skip the full building-permit process, though a setback of Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011. still applies. Confirm your lot's zoning district before ordering, since setbacks vary by district.
Delivery to Reevesville
Current delivery time to Reevesville is approximately 1 to 2 weeks. Benton also serves nearby communities including Badham, Dorange, Grover and Byrd. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Dorchester County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can I put a metal garage beside my house?
You may be able to, but don't assume every open spot on the property is buildable. Dorchester County Building Services Department has requirements that can affect garage placement, including a current setback of Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.. Check the rules for your address before choosing the location, particularly if you're working with limited room between the house and property line.
How much extra room should I allow around my vehicles?
Don't measure a car and make the garage barely wider than the vehicle. You need enough room to open the doors, get in and out, walk around it and reach anything stored nearby. With two vehicles, remember the space between them too. Adding a little breathing room during planning can make a big difference once you use the garage every day.
Do I need a permit for a metal garage in Reevesville?
That depends on the garage and the requirements of Dorchester County Building Services Department. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Reevesville before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
Definitions
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Fastener
- A screw or other connector used to hold metal panels and building components securely in place.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Roof Pitch
- How steep the roof is, usually described by how much it rises over a set horizontal distance.
Reevesville, Dorchester County — At a Glance
- Permit Authority Name
- Dorchester County Building Services Department
- Permit Authority Url
- https://www.dorchestercountysc.gov/government/building-services/submittal-process
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
- Wind Load Zone
- Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 108.9
- Drive Minutes
- 146
- Nearby Towns
- Badham, Dorange, Grover, Byrd
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Reevesville and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Reevesville?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.dorchestercountysc.gov/government/building-services (2026)
- https://www.dorchestercountysc.gov/government/building-services/submittal-process (2026)
- South Carolina Residential Code § R105.2 (2018 IRC as adopted statewide, incl. Dorchester County): one-story detached accessory structures used as tool/storage sheds, playhouses, etc. are exempt from a building permit if floor area ≤200 sq ft AND the structure has no electrical/plumbing/mechanical connections. Not independently re-confirmed on Dorchester's own permitting page (403'd on fetch) — verify against Dorchester's current submittal guide before publishing. (2026)
- https://www.dorchestercountysc.gov/government/planning-development/planning-zoning/zoning-and-land-development-standards (2026)
- General ASCE 7 coastal-plain-SC range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Dorchester County is not among the coastal counties named in the client spec, though it borders Charleston and Berkeley counties (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
