Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Giant and across Dorchester, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
- ◦Doors, windows and other selections can change the final cost of a garage.
- ◦The current local setback for a metal garage is Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011..
- ◦Get the final garage dimensions before completing permanent site work.
- ◦Benton serves Harleyville, Dorchester, Pregnall and Grover and other communities around Giant.
At a Glance
| Permit threshold |
200
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
As of 2026 · Source |
| Wind load zone |
Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
164
As of 2026 · Source |
Permits & Setbacks in Dorchester County
The permit question for a Giant metal garage comes down to one number from Dorchester County Building Services Department: 200 square feet. Stay under it and skip the full permit process; either way, keep the Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011. setback in mind before you pick a spot.
Delivery to Giant
Current delivery time to Giant is approximately 1 to 2 weeks. Benton also serves nearby communities including Harleyville, Dorchester, Pregnall and Grover. Before delivery gets close, make sure you've handled the local permits and any site preparation needed for your particular garage.
Representative product photo — a Dorchester County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Giant, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
Do I need a permit for a metal garage in Giant?
That depends on the garage and the requirements of Dorchester County Building Services Department. The current rule requires a permit once the garage exceeds 200 square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Dorchester County Building Services Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Can my metal garage have windows and different doors?
The available configuration depends on the garage package, but doors and windows should be considered while you're planning the layout. Think about where vehicles will enter, where you want a regular walk door and whether natural light is needed inside. Making those decisions early helps you choose a layout that works instead of adding features wherever they'll fit.
How long does it take to get a metal garage delivered to Giant?
Current delivery time to Giant is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Walk Door
- A regular entry door that lets you enter the garage without opening one of the larger vehicle doors.
- ◦ Concrete Slab
- A flat poured-concrete surface commonly used as the finished floor and part of the foundation system for a garage.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Ridge
- The top line of a pitched roof where the two sloping sides come together.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
Giant, Dorchester County — At a Glance
- Permit Authority Name
- Dorchester County Building Services Department
- Permit Authority Url
- https://www.dorchestercountysc.gov/government/building-services/submittal-process
- Permit Threshold Sqft
- 200
- Setback Feet Side Rear
- Not confirmed with specific figures. Dorchester County's Zoning and Land Development Standards govern accessory-structure setbacks by district, but the exact side/rear setback numbers could not be retrieved (page returned 403 on fetch). Verify against the primary ordinance or by calling Planning & Zoning at (843) 832-0011.
- Wind Load Zone
- Coastal-plain South Carolina, closer to the coast than Aiken/Berkeley's inland portions (Dorchester borders Charleston/Berkeley counties) — roughly 120-140 mph (ASCE 7, Exposure C/D). NOT a verified figure; the exact design wind speed depends on the ASCE 7/IBC edition Dorchester County has adopted and must be confirmed with an SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 131.8
- Drive Minutes
- 164
- Nearby Towns
- Harleyville, Dorchester, Pregnall, Grover
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Buying a garage isn't just a matter of picking a picture and choosing a size. You also have to think about what you're putting inside, where it will sit and what materials the project needs. Benton Metal Depot works with residents in Giant and throughout the region to help them choose a garage package that will work well with whatever they need.
Ready to talk through your metal garages project in Giant?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.dorchestercountysc.gov/government/building-services (2026)
- https://www.dorchestercountysc.gov/government/building-services/submittal-process (2026)
- South Carolina Residential Code § R105.2 (2018 IRC as adopted statewide, incl. Dorchester County): one-story detached accessory structures used as tool/storage sheds, playhouses, etc. are exempt from a building permit if floor area ≤200 sq ft AND the structure has no electrical/plumbing/mechanical connections. Not independently re-confirmed on Dorchester's own permitting page (403'd on fetch) — verify against Dorchester's current submittal guide before publishing. (2026)
- https://www.dorchestercountysc.gov/government/planning-development/planning-zoning/zoning-and-land-development-standards (2026)
- General ASCE 7 coastal-plain-SC range (aggregated secondary sources) — no county-specific or primary map source found (2026)
- Dorchester County is not among the coastal counties named in the client spec, though it borders Charleston and Berkeley counties (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
