Reviewed by the Benton Metal Depot team · Updated
Are you running out of room in the driveway, shed or workshop? A metal garage can put vehicles, tools and equipment under one roof. Benton Metal Depot supplies garage packages to customers in Lena and across Hampton, with different building sizes depending on the amount of space the property owner needs.
Key Points
- ◦Delivery to Lena is currently estimated at 1 to 2 weeks.
- ◦Check the permit and setback rules before deciding exactly where the garage will go.
- ◦Benton Metal Depot is approximately 57.1 miles from Lena.
- ◦A metal garage can be used as parking, storage, equipment and work space under the same roof.
- ◦Plan for door clearance and walking room when deciding how wide your garage needs to be.
At a Glance
| Permit threshold |
Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127).
As of 2026 · Source |
|---|---|
| Setback (side/rear) |
Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup.
As of 2026 · Source |
| Wind load zone |
Inland South Carolina (Lowcountry interior) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
As of 2026 · Source |
| Panel type/gauge |
29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
As of 2026 · Source |
| Drive time from Statesboro |
92
As of 2026 · Source |
Permits & Setbacks in Hampton County
The permit question for a Lena metal garage comes down to one number from Hampton County Building & Planning Department: Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127). square feet. Stay under it and skip the full permit process; either way, keep the Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup. setback in mind before you pick a spot.
Delivery to Lena
Residents in Lena are currently looking at about 1 to 2 weeks after placing an order. Benton Metal Depot is approximately 57.1 miles away. Use that window to finish whatever needs to happen at the property first. Waiting until the garage is ready can create unnecessary delays if the site isn't.
Representative product photo — a Hampton County-specific project photo is pending (rotates in from Trey's weekly upload per the freshness cadence).
FAQ
Can I use my metal garage as a workshop too?
Definitely! Just plan for the workshop before deciding on the garage size. A workbench, toolboxes, shelving and equipment can eat up a lot of floor space, especially when you're also parking a vehicle inside. Make sure to give yourself enough room to work comfortably instead of trying to fit a workshop into whatever space happens to be left over.
Are metal garages a good choice for Georgia?
Metal buildings are utilized throughout Georgia for garages, equipment storage and other residential, agricultural and commercial uses. The important thing is choosing a building appropriate for the project and location. If you're building in Lena, make sure the garage specifications and site plan also meet the local requirements that apply to the property.
What do I need to do to my property before the garage arrives?
First, decide exactly where the garage will go and check the permit and setback requirements with Hampton County Building & Planning Department. Then follow the site requirements for the garage you've selected. Any grading, concrete or other preparation should be based on the final building specifications. Don't prepare the site using rough dimensions if the building hasn't been finalized.
Can I use a metal garage just for storage?
Yes. Cars don't have to be part of the equation at all. A metal garage can give you enclosed space for tools, lawn equipment, recreational gear and other belongings. If storage is the main purpose, think about shelving and aisle space while planning the building so everything remains accessible once the garage starts filling up.
Do I need a permit for a metal garage in Lena?
That depends on the garage and the requirements of Hampton County Building & Planning Department. The current rule requires a permit once the garage exceeds Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127). square feet. Check before doing any permanent site work. There may be other requirements tied to your property as well, so getting an answer early can save you from having to change plans later.
Should I pour the concrete before ordering the garage?
Get the garage specifications nailed down first. You want to know the correct dimensions and make sure the planned location meets the rules for Lena before putting permanent concrete in the ground. It's much easier to adjust a garage plan on paper than to deal with a slab that was poured in the wrong place or at the wrong size.
How long does it take to get a metal garage delivered to Lena?
Current delivery time to Lena is approximately 1 to 2 weeks. If your project also involves permitting, grading or concrete, don't wait to do those jobs until the garage is almost ready. Use the delivery window to get the property prepared, and base your schedule on the estimate given for your order.
What can I keep in a metal garage?
Cars and trucks are obvious, but metal garages can also hold lawn equipment, tools, recreational gear and general storage. Larger buildings can leave room for work areas, too. Make a list of what you intend to keep inside before choosing the building size. It's easy to underestimate how quickly floor space disappears.
Definitions
- ◦ Wall Panel
- Formed metal sheet used to enclose and protect the exterior walls of the garage.
- ◦ Clear Span
- Open floor space between the building's exterior supports without interior columns getting in the way.
- ◦ Overhead Door
- The large door that opens upward to let cars, trucks or equipment move in and out of the garage.
- ◦ Building Permit
- Approval from the local government to construct a building under the building and zoning rules that apply to the property.
- ◦ Setback
- The required amount of space between your garage and a property line, road or another boundary covered by local rules.
- ◦ Gable
- The triangular wall section found at the end of a building with a pitched roof.
- ◦ Eave Height
- The height of the sidewall measured to the point where the wall and roof meet.
- ◦ Trim
- The finished metal pieces used along corners, roof edges, openings and other transitions on the building.
- ◦ Roof Panel
- A formed sheet of metal that makes up part of the garage's exterior roof surface.
- ◦ Building Footprint
- The amount of ground the garage takes up, based on its outside width and length.
Lena, Hampton County — At a Glance
- Permit Authority Name
- Hampton County Building & Planning Department
- Permit Authority Url
- https://www.hamptoncountysc.org/9/Building-Planning-Department
- Permit Threshold Sqft
- Not found — no explicit sqft exemption for accessory structures located on the county site; the county publishes an "Accessory Building Use Form" but a size-based exemption was not confirmed. Needs direct confirmation (803-914-2127).
- Setback Feet Side Rear
- Not retrieved — Hampton County zoning setback tables for accessory structures were not found in available search results (note: the Town of Hampton has its own separate 2010 zoning ordinance, distinct from Hampton County). Needs direct county ordinance lookup.
- Wind Load Zone
- Inland South Carolina (Lowcountry interior) — roughly 115-120 mph (ASCE 7, Exposure C). NOT a verified figure; must be confirmed with a SC-licensed engineer or the county building official.
- Coastal
- Drive Miles
- 57.1
- Drive Minutes
- 92
- Nearby Towns
- Speaks Mill, Lawtonville Crossroads, Nixville, Estill
- Delivery Weeks In Stock
- 1
- Delivery Weeks Custom
- 2
- Panel Type Gauge
- 29-gauge and 26-gauge Rib panels -- Benton's existing standard gauge/profile for pole-barn, carport, and agricultural structures.
- Color Count
- 7
Why Benton Metal Depot
Benton Metal Depot has been working with metal building products in Statesboro since 2004. That local experience is important when you're planning a garage in Lena and trying to sort through materials, building specifications and the rest of the project details. Benton works with homeowners, contractors and property owners throughout the region.
Ready to talk through your metal garages project in Lena?
Sources
- Internal: category-data.php (pole-barns / agricultural-pole-barns copy) (2026)
- color-collection.php Weather XL Rib/PBR color chart: Polar White, Pebble Gray, Granite, Onyx, Vanilla, Sand, Chocolate (29ga; 5 of the 7 also available in 26ga). Real Benton color count for this panel line -- not confirmed as the specific palette Jim/Trey intend to offer for metal garages. (2026)
- https://www.hamptoncountysc.org/9/Building-Planning-Department (2026)
- https://www.hamptoncountysc.org/349/Ordinances — needs direct lookup (2026)
- General ASCE 7 inland-SC range (windload.solutions and similar secondary sources) — no county-specific primary map source found (2026)
- Given/client spec — Hampton County is inland South Carolina (2026)
- Computed 2026-09-16: GeoNames zip centroid -> OSRM public routing engine (real driving route from Statesboro, Bulloch County, GA). Deterministic and reproducible, but a free public demo routing server, not Google Maps -- spot-check a sample before confirming. (2026)
- Computed 2026-09-16: same OSRM routing result as drive_miles, converted from seconds. (2026)
- Computed 2026-09-16: 4 nearest cities in benton_service_area_cities.php by straight-line (haversine) distance from zip centroid. (2026)
- Bulk-set via dev-fact-review.php (2026)
Other Cities We Serve in Hampton County
See the Hampton County hub for metal garages
